Instruction Manual

ManualsBrandsAmerican Lighting ManualsSPKPLGTWYEAMERICAN LIGHTING SPKPL-GTWY-E Spektrum+ Gateway with Ethernet Port

Page 1 of 1

SPKPL-GTWY-E

INSTALLATION INSTRUCTIONS

120V

Spektrum+ Gatew ay w ith Ethernet Port

SAFETY INFORMATION

• Read all instructions before beginning; Save these instructions for future use.

• To reduce the risk of ﬁre, electric shock, or injury to persons, pay close attention

to this manual and stay within its guidelines when using this product.

• If you are unsure about your wiring, consult a qualiﬁed electrician or local electrical

inspector, and check your local electrical code.

• There are no serviceable parts inside this gateway. Do not attempt to dismantle,

open or service this gateway in any way.

• The optimal operating temperature of this product is -10°C (14°F) to 55°C (131°F).

• Thie gateway requires a 2.4Ghz WiFi or Ethernet signal to operate.

• This gateway is not intended for use with a standard wall plate dimmer switch. Use

only with Spektrum+ Smart Lighting App

• This gateway is rated for dry/indoor locations only. Keep away from all water and

moisture.

These products may represent a possible shock or

ﬁre hazard if improperly installed or attached in any

way. Products should be installed in accordance

with these instructions, current electrical codes,

and/or the current National Electric Code (NEC).

The electrical rating of this product is 5V DC and

utilizes a 120V AC power adapter. The installer

must determine whether power supply is appro-

priate before installation. Ensure power supply is

turned o at the fuse box or circuit breaker prior to

attempting installation or servicing of the gateway.

WARNING

INSTALLATION INSTRUCTIONS:

This ﬁxture requires a 120VDC power source.

1. Place gateway within 18” of power receptacle.

2. Plug mini USB power adapter into Gateway. See Figure 1.

3. Plug power adapter into receptacle. The blue power indicator light on the Gateway will light when powered. See Figure 2.

4. Use the Ethernet port if connecting to Ethernet router.

5. Pair device to Spektrum+ Smart Lighting app on your mobile phone or tablet. For pairing instructions please refer to the Spektrum+ Smart

Lighting app guide or quick start guide.

Resetting the ﬁxture

1. To reset the gateway, press and hold the Reset Button for 5 seconds until the WIFI indicator light ﬂashes.

Indicator light status

Red Light: WiFi Status

1. Long light indicates connected.

2. Blinking indicates pending connection.

Blue light:

2. Long o indicates activated.

Long light indicates inactive.

Blinking indicates that the sub-device is allowed to access the network.

FIGURE 1

FIGURE 2

Reset Button

Ethernet Port

WiFi

Indicator

MESH

Inidicator

Summary of content (2 pages)

PAGE 1
20V Spektrum+Gatew ay w ith Eth ern etPo rt INSTALLATION INSTRUCTIONS SPKPL-GTWY-E SAFETY INFORMATION WARNING These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC). WARNING The electrical rating of this product is 5V DC and utilizes a 120V AC power adapter.
PAGE 2
FCC Caut i on: Thi s devi ce compl i es wi t h par t 15 of t he FCC Rul es. Oper at i on i s subj ect t o t he f ol l owi ng t wo condi t i ons: ( 1) t hi s devi ce may not cause har mf ul i nt er f er ence, and ( 2) t hi s devi ce must accept any i nt er f er ence r ecei ved, i ncl udi ng i nt er f er ence t hat may cause undesi r ed oper at i on.