Installation Guide

ManualsBrandsAmerican Standard ManualsPedestal Sink Bases0039000.020

SAVE FOR FUTURE USE

7302242-100 Rev. A

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

Edgemere

™

0445 Series Console / Pedestal

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

OBSERVE LOCAL PLUMBING AND BUILDING CODES

Recommended Tools & Materials

Edgemere Console Lavatory Edgemere Pedestal Lavatory

Adjustable Wrench

Channel Lock Pliers

Regular Screwdriver

Phillips Screwdriver

Pipe Wrench

Putty Knife

Drill

Saber Saw

Basin Wrench

Plumbers' Putty or

Caulking

Tubing Cutter

Tape Measure

Hacksaw

Level

FINISHED

FLOOR

FOR

ANCHOR

SCREW

MOUNT

FINISHED

WALL

FINISHED

WALL

906mm

(35-11/16")

496mm

(19-1/2")

112mm

(4-7/16")

160mm

(6-5/16")

40mm

(1-9/16")

545mm

(21-1/2")

213mm

(8-3/8")

775mm

(30-1/2")

710mm

(28")

866mm

(34-1/16")

207mm

(8-1/8")

622mm

(24-1/2")

634mm

(25")

102mm

(4")

444mm

(17-1/2")

514mm

(20-1/4")

140mm

(5-1/2")

OPEN TO

FLOOR

FINISHED WALL

OR BACKSPLASH

SUPPLIES

AS REQ'D

1-1/4" O.D.

WASTE

1-1/4" O.D.

TAILPIECE

FINISHED

FLOOR

*578mm

(22-3/4")

*521mm

(20-1/2")

202mm

(8")

213mm

(8-3/8")

22mm

(7/8")

102mm

(4")

215mm

(8-1/2")

634mm

(25")

495mm

(19-1/2")

DRAIN CHASE

50mm

(2")

203mm

(8")

906mm

(35-5/8")

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Edgemere™ 0445 Series Console / Pedestal Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
8719 CONSOLE TABLE COMPONENTS LIST A B ITEM # QTY. A B C D E F G 1 1 1 1 2 1 8 DESCRIPTION LEFT SIDE LEG SUB-ASSEMBLY RIGHT SIDE LEG SUB-ASSEMBLY BACK TOP SUPPORT TUBE TOWEL BAR SHELF SUPPORT TUBE TEMPERED GLASS SHELF M4 x 0.7 PHILLIPS HEAD MACHINE SCREW C F D E G CONSOLE ASSEMBLY 1 Insert the back top support tube (C) as well as both shelf support tubes (E) into the exposed tube housings in the left side leg sub-assembly (A) as shown.
PAGE 3
PEDESTAL AND CONSOLE LAVATORY INSTALLATION 1 Wall Preparation for Sink and Pedestal/Console Installation Provide suitable reinforcement behind finished wall for sink hanger screws. For an installed sink height of 35-5/8" (905mm) center the reinforcement 33-5/8" (854mm) above the floor C/L of 2 x 6 Support and Bracket 33-5/8" (854mm) Note: If replacing an existing sink be certain to shut off water supply prior to removing old sink. Finished Floor 2 1.
PAGE 4
Faucet and Drain Installation 1. A Following manufacturer’s instructions, install faucet and drain assembly (not included). 2. Apply a bead of sealing putty on the underside of the drain (see detail A) in order to ensure a watertight seal between the sink and the drain. Remove excess putty after installing drain on sink. 3. Return the sink assembly to the installed position, guiding the sink over the two headless hanger screws. 4. Connect the trap to drain assembly and hand-tighten to check alignment.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN CUIDADO Y MANTENIMIENTO Consola/Pedestal serie 0445 Edgemere™ Gracias por elegir American Standard, el parámetro de excelente calidad por más de 100 años. Para asegurarse de que este producto se instale de manera adecuada, lea las instrucciones atentamente antes de comenzar. (Para algunas instalaciones, puede necesitarse ayuda profesional). Asegúrese también de realizar la instalación de conformidad con los códigos locales. ! PRECAUCIÓN: EL PRODUCTO ES FRÁGIL.
PAGE 6
LISTA DE COMPONENTES DE LA MESA DE CONSOLA 8719 A N.º DE ARTÍCULO B CANT.
PAGE 7
INSTALACIÓN DEL LAVABO CON PEDESTAL Y CONSOLA 1 Preparación de la pared para instalar el lavabo con pedestal/consola Instale un refuerzo adecuado detrás de la pared terminada para colocar los tornillos de suspensión del lavabo. Para un lavabo instalado a una altura de 35-5/8" (905 mm), centre el refuerzo a 33-5/8" (854 mm) por encima del piso.
PAGE 8
4 Instalación de llave y desagüe A 1. Siguiendo las instrucciones del fabricante, instale el conjunto de llave y desagüe (no incluido). 2. Aplique una gota de masilla selladora en la parte inferior del desagüe (vea el detalle A) a fin de garantizar un sellado hermético entre el lavabo y el desagüe. Quite el exceso de masilla después de instalar el desagüe en el lavabo. 3.
PAGE 9
INSTRUCTIONS D’INSTALLATION NETTOYAGE ET ENTRETIEN Edgemere™ série 0445 sur console/colonne Merci d’avoir choisi American Standard, la référence en matière de qualité depuis plus de 100 ans. Afin de garantir une installation adéquate, veuillez lire attentivement ces instructions avant de commencer. (Certaines installations peuvent requérir l’aide d’un professionnel.) De plus, assurez-vous que votre installation soit en conformité avec le code local. ! MISE EN GARDE : PRODUIT FRAGILE.
PAGE 10
8719 LISTE DES ÉLÉMENTS DE LA CONSOLE A NO D’ARTICLE B A B C D E F G QTÉ 1 1 1 1 2 1 8 DESCRIPTION SOUS-ASSEMBLAGE DU PIED GAUCHE SOUS-ASSEMBLAGE DU PIED DROIT TUBE-SUPPORT SUPÉRIEUR ARRIÈRE PORTE-SERVIETTE TUBE-SUPPORT DE LA TABLETTE TABLETTE EN VERRE TREMPÉ M4 x 0,7 VIS D’ASSEMBLAGE CRUCIFORMES C F D E G ASSEMBLAGE DE LA CONSOLE 1 Faites glisser le tube-support supérieur arrière (C) ainsi que les deux tubes-supports de la tablette (E) dans les boîtiers de tube apparents dans le sous-assemblage
PAGE 11
INSTALLATION DU LAVABO SUR CONSOLE ET SUR COLONNE 1 Préparation du mur pour l’installation du lavabo sur colonne et sur console Installez un renforcement adéquat à l’arrière du mur fini pour les vis du support du lavabo. Pour un lavabo installé à une hauteur de 35-5/8 po (905 mm), centrez le renforcement à 33-5/8 po (854 mm) du sol.
PAGE 12
4 Installation du robinet et du drain A 1. Selon les instructions du fabricant, installez l’assemblage du robinet et du drain (non inclus). 2. Appliquez un trait de mastic d’étanchéité sur le côté inférieur du drain (voir détail A) afin d’assurer l’étanchéité entre le lavabo et le drain. Enlevez l’excédent de mastic après avoir installé le drain sur le lavabo. 3. Retournez l’assemblage du lavabo à la position d’installation, tout en guidant le lavabo sur les deux vis de support sans tête. 4.