Installation Guide

ManualsBrandsAmerican Standard ManualsBathroom SinksWhite Wall-Mount Rectangular Bathroom Sink with Overflow Drain

Adjustable Wrench

Channel Lock Pliers

Regular Screwdriver

Recommended Tools & Materials

Phillips Screwdriver

Pipe Wrench

Putty Knife

Drill

Saber Saw

Basin Wrench

Plumbers' Putty or Caulking

Tubing Cutter

Tape Measure

Hacksaw

NOTE: For installation of models using concealed or exposed arms, follow instruction provided by arms manufacturer.

Level

SAVE FOR FUTURE USE

730427-100 Rev. 8 8/20

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

WALL HUNG SINK

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

OBSERVE LOCAL PLUMBING AND BUILDING CODES

Provide suitable reinforcement behind

finished wall for lavatory hanger

mounting screws. *Determine

horizontal center line location of

support from the table listed in Step 2.

(Make sure support bottom extends to

lavatory back wall bottom.)

NOTE: If replacing an existing sink be

certain to shut off water supply before

removing old sink.

Hanger

Location

C/L of 2 x 8

Support

Finished

Floor

Drill pilot holes in positioning screw

slots of hanger. Note: Some models

are supplied with anchor screws, or

steel hangers for lavatory installations.

Other models are not provided with

mounting hardware which can be

purchased at local hardware outlets.

Lavatories with bottom anchor screw

holes should be secured with anchor

screws in addition to hangers.

MOUNTING

SCREW

HOLES (4)

POSITIONING

SCREW

SLOTS (2)

Position hanger according to Step 2,

making sure its center is aligned with

the waste hole centerline. Mark the

hanger screw locations through its

mounting holes.

Determine the

desired rim height

(for example 32")

then select from the

Table at right the

height of the hanger

mounting bolts

centerline

EXAMPLE:

For Comrade:

32" - 2-1/2" = 29-1/2"

Part # Model

TABLE

Distance "A"

0124

0321

0355/0356

0372/0373

4867/4869

9024

9134

Comrade

Declyn

Lucerne

Penlyn

Regalyn

Decorum

18-1/4" x 20-1/16"

Decorum

20-1/2" x 21-1/4"

- 2-1/2" (64mm)

- 2-3/4" (70mm)

- 1" (25mm)

- 1/8" (3mm)

+ 2-3/4" (70mm)

- 3-11/16" (93mm)

HOLES FOR

ANCHOR SCREWS

IN BACK DRAPERY

RIM

HEIGHT

SUPPLIES

AS REQUIRED

WASTE

FINISHED FLOOR

HANGER

C/L OF HANGER ANCHORING SLOTS

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE WALL HUNG SINK NOTE: For installation of models using concealed or exposed arms, follow instruction provided by arms manufacturer. Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 2
5 Affix hanger to wall (hand tighten only). Mount lavatory for positioning, level the deck, and mark bottom anchor screw holes (if applicable). Remove lavatory, tighten the hanger positioning screws and drill pilot holes for anchor screws and 4 mounting screws. Install and tighten the mounting screws. 6 Following manufacturers instructions, install faucet and drain assembly. (Not included).