Installation Guide

ManualsBrandsAmerican Standard ManualsBathRavenna Wall-Mount Pedestal Combo Bathroom Sink in White

Pedestal

Anchor Holes

Access

730515-100 Rev. B

7/16" Wrench

Channel Lock Pliers

Regular Screwdriver

Phillips Screwdriver

Pipe Wrench

Putty Knife

Drill

Saber Saw

Basin Wrench

Plumbers' Putty or

Caulking

Tubing Cutter

Tape

Measure

Hacksaw

Pencil

3/16 Dia. Drill

9/32 Dia. Drill

Level

*NOTE: For ease of installation and accessibility, it is recommended that straight stops with flex supply tubes be used.

As an alternative, if rigid supply risers are used, it is suggested to use angle stops in place of the straight stops.

9/16" Wrench

Install lavatory anchor screws leaving

1-5/8" (41mm) threaded end exposed as illustrated.

1-5/8"

(41mm)

ANCHOR SCREW INSTALLATION

Anchor

Screw

Washer

Lavatory

Nut

(230mm)

(76mm)

26-1/2"

(673mm)

21"

(533mm)

24-3/4"

(629mm)

32"

(813mm)

SUPPLIES

7/8" x 4"

(22mm x 102mm)

HANGER STUDS

DRYWALL

DOUBLE

2" x 8"

50 x 203mm

WOOD

BRACE

FINISHED

FLOOR

WASTE

Provide Rough-in: Install waste pipe

21" (533mm) up from the floor. Install

the supplies at 24-3/4" (629mm) up

from finished floor, spaced 1-1/2"

(38mm) to either side of centerline.

Firmly attach two 2" x 8" (50 x 203mm)

wood braces to wall studs. Bottom of

brace should be 26-1/2" (673mm) up

from floor and extend a minimum of 6"

(153mm) to either side of waste.

Complete drywall installation

(see figure 1).

SINK

ANCHOR

HOLES

SEMI-PEDESTAL/SHROUD

ANCHOR HOLES

Drill (2) 9/32" dia. (7mm) holes 32" (813mm) up from finished floor,

spaced at 4-3/4" (120.6mm) either side of centerline. Install (2) 3/8" x 4"

(10mm x 102mm) lg studs using the double nut method, leaving 1-5/8"

(41mm) of threaded end exposed. Mount the sink to studs temporarily,

making sure the sink is level side to side.

Position semi-pedestal under bottom lip of sink. While holding

semi-pedestal in position reach through the access area between

the lavatory and semi-pedestal and mark the location of anchor

holes. Remove semi-pedestal and predrill 3/16" (4-5mm) dia. holes

at locations marked. Install 1/4" x 3" lg studs leaving 1-1/4"

exposed. Use same anchor screw installation as in 2a.

Recommended Tools & Materials

SAVE FOR FUTURE USE

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

Ravenna Wall-Hung Semi-Pedestal Sink

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

OBSERVE LOCAL PLUMBING AND BUILDING CODES

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Ravenna Wall-Hung Semi-Pedestal Sink Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
3 Remove lavatory top. Install faucet and pop-up assembly ("A") according to manufacturer's instructions before installing sink. Remount sink on the threaded end of wall studs. Firm up with washers and nuts, but do not over-tighten. It may be necessary to cut off part of the tailpiece (area "B") or part of the horizontal leg of the trap (area "C"). 4 Connect water supplies lines and drain pipe connections. Turn water on and check for leaks.