Use & Care Guide

J48
BARRIER FREE
© 2008 AS America Inc.
STUDIO™ UNDERCOUNTER SINK
• Rectangular undercounter mount sink
• Made from vitreous china
• Front overow
• Supplied with mounting kit (047194-0070A)
and template
❏ 0614.000 Unglazed Rim
540 x 387mm
(21-1/4" x 15-1/4")
❏ 0614.300 Glazed underside
Bowl size:
464mm (18-1/4") wide
308mm (12-1/8") front to back
171mm (6-3/4") deep
❏ 0618.000 Unglazed Rim
600 x 422mm
(23-5/8" x 16-5/8")
❏ 0618.300 Glazed underside
Bowl size:
537mm (21-1/8") wide
356mm (14") front to back
152mm (6") deep
Compliance Certications -
Meets or Exceeds the
Following Specications:
• ASME A112.19.2M for
Vitreous China Fixtures
• CAN/CSA B45 series
STUDIO™
UNDERCOUNTER SINK
VITREOUS CHINA
To Be Specied:
❏ Color: ❏ White ❏ Bone
❏ Linen ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
● Countertop 864mm (34") from finished floor. Lavatory
installed 102mm (4") from front edge of countertop.
Countertop thickness to be 25mm (1") maximum.
NOTES:
WE RECOMMEND USING BASIN AS A TEMPLATE TO DETERMINE PROPER
CONTOUR. CUT COUNTERTOP 38MM (1-1/2") INSIDE BASIN CONTOUR.
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIED AND “P" TRAP ARE
SUGGESTED.
▼ UNDERCOUNTER MOUNTING KIT SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
51mm
(2) MIN.
83mm
(3-1/4)
FINISHED WALL
OR SPLASHBACK
C
EDGE OF
COUNTER
TOP
CUTOUT
A
B
41mm
(1-5/8)
E
F
DETAIL OF MOUNTING CLIP
(KIT No.47194.0070A)
LAVA
BRASS
INSERT
19mm
(3/4) MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
1-1/4 O.D.
TAILPIECE
1-1/4 O.D.
WASTE
203mm
(8)
38mm
(1-1/2)
330mm
(13)
273mm
(10-3/4)
13mm
(1/2)
D
SUPPLIES
AS REQ'D.
ADA DRAIN
OUTLET
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
864mm
(34)
*
279mm
(11)
*
*
FINISHED FLOOR
22mm
(7/8)
FITTING
CENTER-SET
SPREAD
A
1-1/16 (27mm)
1-1/4 (32mm)
B
4 (102mm)
8 (203mm)
G
H
CAT. NO.
0614.000
E
540mm
(21-1/4)
600mm
(23-5/8)
F
387mm
(15-1/4)
422mm
(16-5/8)
G
464mm
(18-1/4)
537mm
(21-1/8)
H
308mm
(12-1/8)
356mm
(14)
0618.000
864mm
(34)
102mm
(4)
D
209mm
(8-1/4)
209mm
(8-1/4)
C
114mm
(4-1/2)
108mm
(4-1/4)
610mm
(24)
152mm
(6)
MAX.
BARRIER FREE
CLEARANCE
686mm
(27)
MIN.
203mm
(8)
MIN.
229mm
(9)
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
Revised 2/08