Specification

M12
© 2015 AS America Inc.
MURRO
™
UNIVERSAL DESIGN
WALL-HUNG LAVATORY WITH EVERCLEAN
®
VITREOUS CHINA/ACRYLIC
MURRO WITH ACRYLIC SHROUD MURRO WITH VITREOUS CHINA SHROUD
NOTES:
● LOOSEKEYANGLESTOPS,LESSWALLESCUTCHEONS.SUPPLIESREQUIRED.
*
DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPARESUGGESTED.
SHROUD/KNEECONTACTGUARD0059.020NOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.
■SUITABLEFORREINFORCEMENTONLY,ACTUALDIMENSIONSMUSTBETAKENFROMFIXTURE.
FITTINGSNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.
PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.
INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.
IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.2.
Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages.
spec_0954-0955-0958 Murro Wall Hung Rev A 8/15
FAUCET HOLE SPREAD AND DIAMETER
A
B
4" (102mm)
Ø 31.8mm, 1-1/4" ± 1/8" (3mm)
8" (203mm)
Ø 35mm, 1-3/8" + 1/8" - 1/16" (+3mm/-1.5mm)
550 mm
(21-7/16")
200 mm
(7-7/8")
85 mm
(3-5/16")
(2) 54 mm (2-1/8")
DIA. PUNCH
FOR CONC. ARMS
102 mm
(3-15/16")
152 mm
(5-15/16")
102 mm
(3-15/16")
455 mm
(17-3/4")
65 mm
(2-9/16")
152 mm
(5-15/16")
565 mm
(22-1/4")
864 mm
(34")
743 mm
(29-1/4")
SIDE PROFILE
(ADA)
SEE CHART FOR
DIAMETER OF
FAUCET HOLES
B
A
168 mm
(6-9/16")
168 mm
(6-9/16")
Ø35 mm
(Ø1-3/8")
Ø15 mm
(Ø9/16")
265 mm
(10-5/16")
399 mm
(15-9/16")
433 mm
(16-7/8")
FINISHED FLOOR
FINISHED WALL
FINISHED WALL
FINISHED FLOOR
(6) 25 mm (1") DIA.
ACCESS HOLES
FOR CONC. ARMS
SIDE PROFILE
(ADA)
(2) 54 mm (2-1/8")
DIA. PUNCH
FOR CONC. ARMS
65 mm
(2-9/16")
152 mm
(5-15/16")
419 mm
(16-3/8")
864 mm
(34")
160 mm
(6-1/4")
Ø15 mm
(Ø9/16")
Ø15 mm
(Ø9/16")
399 mm
(15-9/16")
433 mm
(16-7/8")
127 mm
(4")
FINISHED FLOOR
743 mm
(29-1/4")
267 mm
(10-7/16")
FINISHED WALL
FINISHED FLOOR
550 mm
(21-7/16")
200 mm
(7-7/8")
85 mm
(3-5/16")
102 mm
(3-15/16")
152 mm
(5-15/16")
102 mm
(3-15/16")
455 mm
(17-3/4")
SEE CHART FOR
DIAMETER OF
FAUCET HOLES
B
A
168 mm
(6-9/16")
168 mm
(6-9/16")
Ø35 mm
(Ø1-3/8")
FINISHED WALL
(6) 25 mm (1") DIA.
ACCESS HOLES
FOR CONC. ARMS
FAUCET HOLE SPREAD AND DIAMETER
A
B
4" (102mm)
Ø 31.8mm, 1-1/4" ± 1/8" (3mm)
8" (203mm)
Ø 35mm, 1-3/8" + 1/8" - 1/16" (+3mm/-1.5mm)