Installation Guide

ManualsBrandsAmerican Standard ManualsBathMetering 8 in. Widespread 2-Handle Bathroom Faucet in Polished Chrome

M968492 Rev.1.5

Certiﬁed to comply with ANSI A112.18.1M

PREPARE TUBE AND TEE ASSEMBLY

VALVE ASSEMBLY (1340.825; 1340.855; 1340.865)

1340.725

1340.825

1340.827

1340.855

1340.857

1340.865

Remove COUPLING NUT (1) and FERRULE (2) from each

VALVE (3) and slide onto TUBING (4).

Push TUBING (12) ends into VALVE (4) side outlets. Insert

VALVES (4) into mounting holes from underside of ledge.

Install LOCKNUTS (1), METAL WASHERS (3) and RUBBER

WASHERS (2) onto valve shanks.

Place RUBBER RING (8) into ESCUTCHEONS (7) and thread onto

valves until snug against internal stop.

Tighten LOCKNUT (1) to secure VALVE (4) position.

Slide FERRULE (10) and COUPLING NUT (11) to outlet of VALVE (4)

and tighten COUPLING NUT (11) ﬁrmly.

Place WASHER (14) on top of VALVE ASSEMBLY (4).

COLD

MOUNTING

SURFACE

Attention; Sealing washer (5) should be

replaced everytime valve actuator (4)

is removed.

MOUNTING

SURFACE

SPREAD LAVATORY

FAUCETS

Installation

Instructions

Thank you for selecting American-Standard...the

benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Thread of VALVE BODY (4) should extend at least 5/16 inch above

MOUNTING SURFACE (9). If necessary, adjust LOCKNUT (1).

METERING

1340.725

1340.825

1340.855

1340.865

1340.827

1340.857

Plumbers' Putty or CaulkingAdjustable Wrench 2.5mm Hex Wrench Channel Locks

Recommended tools

REMOVE REPLACE

Remove HANDLE (1) by

removing INDEX BUTTON (2)

and SET SCREW (3) with a

2.5mm hex wrench.

Pull off HANDLE (1).

Remove ACTUATOR

ASSEMBLY (4)

Replace WASHER (5) with

new Washer (5) that is

provided in separate bag.

Thread VALVE ACTUATORS (13) onto VALVES (4) and torque VALVE

ACTUATOR 12-15 ft. lbs, (12-20Nm).

REMOVE HANDLE AND

ACTUATOR ASSEMBLY

HOT

Connect water supply to VALVES (4) with 1/2" IPS FLEXIBLE

SUPPLIES or 3/8" O.D. BULL-NOSE RISERS. Use adjustable wrench

to tighten connections. Do not over tighten. Be careful not to kink

copper supply when bending. Use tubing cutter to cut to proper length.

1/2" IPS FLEXIBLE

SUPPLIES or 3/8" O.D.

BULL-NOSE RISERS

COUPLING NUT

Tubing Cutter

5/16''

MIN.

MOUNTING

SURFACE

Summary of content (3 pages)

PAGE 1
Installation Instructions METERING 1340.725 1340.825 1340.855 1340.865 1340.827 1340.857 SPREAD LAVATORY FAUCETS Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. 1340.725 1340.825 1340.827 1340.855 1340.857 1340.865 Certified to comply with ANSI A112.18.1M To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. M 9 6 8 4 9 2 R ev. 1.
PAGE 2
3a VALVE ASSEMBLY (1340.725) For Cold or Tempered Water Supply Valve assembly is same as two handle lavatory faucets. See Step 3 instructions for assembly, (1340.725 Single Valve Faucet) is for Cold or Tempered water only. 13 7 MOUNTING SURFACE 9 8 14 7 8 5/16'' MIN. 10 4 9 MOUNTING SURFACE 5 6 2 3 4 11 1 COLD OR TEMPERED WATER 12 1/2" IPS FLEXIBLE SUPPLIES or 3/8" O.D. BULL-NOSE RISER COUPLING NUT 4 SPOUT ASSEMBLY CAUTION Turn off hot and cold water supplies before beginning.
PAGE 3
5 1 INSTALL HANDLES Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench. Install HANDLES (4) onto VALVE STEM (5). 4 3 3 4 2.5mm HEX WRENCH Tighten SET SCREWS (3) with 2.5mm Hex Wrench. Replace INDEX BUTTONS. Red (1) in Left HANDLE (4) Blue (2) in Right HANDLE (4). 5 2 6 TEST INSTALLED FITTING Turn on water supplies and check connections for leaks. Remove AERATOR (1) with KEY (2) supplied.