Installation Guide

ManualsBrandsAmerican Standard ManualsBathTraditional 1-Spray Handshower with Adjustable Shower Slide Bar Kit in Brushed Nickel

Installation

Instructions

Certified to comply with ANSI A112.18.1

Recommended Tools & Materials

ROUGHING-IN DIMENSIONS

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Electric Drill

6mm (15/64")

Drill Bit

Pencil

Phillips Screwdriver

1660.225

1660.236

65mm

(2-1/2")

127mm

(5")

900mm

(35-3/8")

82mm

(3-1/4")

70mm

(2-3/4")

25mm

(1")

45mm

(1-3/4")

849mm

(33-3/8")

86mm

(3-3/8")

65mm

(2-1/2")

86mm

(3-3/8")

FINISHED FLOOR

OPTIONAL TO FINISHED FLOOR

USUALLY BETWEEN

915mm

(36")

1525mm

(60")

Hammer

SHOWER SYSTEM KITS

1662 SERIES

1660.505

1660.500

1660.502

1498mm

(59")

32mm

(1-1/4")

13mm

(1/2")

1/2" NPT

RUBBER GASKET

FINISHED WALL

1/2" NPSM HOSE

CONNECTION

53mm

(2-1/16")

(48" - 60")

(OPTIONAL)

TO FINISHED

FLOOR

Turn off hot and cold water

supplies before beginning.

CAUTION

INSTALL WALL SUPPLY

1/2" NPT

APPLY SEALANT

OR TEFLON TAPE

Supply to WALL SUPPLY (1) is 1/2" NPT. See rough-in above for detailed information.

Install RUBBER SEAL (2) onto WALL SUPPLY (1).

Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY (1)

onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL (2)

should be tight against finished wall.

146mm

(5-3/4")

67mm

(2-5/8")

1/2" NPSM

240mm

(9-1/2")

95mm

(3-3/4")

1660.550

250mm

(9-7/8")

42mm

(1-5/8")

57mm

(2-1/4")

120mm

(4-3/4")

1660.843

1660.143

1660.743

1/2" NPSM

266mm

(10-1/2")

116mm

(4-5

/8")

122mm

(4-3/4")

1/2" NPSM

1/2" NPSM 1/2" NPSM

265mm

(10-3/8")

115mm

(4-1/2")

122mm

(4-3/4

)

1/2" NPSM

258mm

(10-1/8")

121mm

(4-3/4")

98mm

(3-7/8")

76mm

(3")

252mm

(9-7/8")

239mm

(9-3/8")

94mm

(3-3/4")

81mm

(3-1/4")

247mm

(9-3/4")

94mm

(3-3/4")

1660.638

1660.628

1/2" NPSM

90mm

(3-1/2")

65mm

(2-1/2")

1660.741

191mm

(7-1/2")

24mm

(1")

1660.609

600mm

(23-5/8")

549mm

(21-5/8")

M968637 Rev 2.0 (4/19)

Summary of content (4 pages)

PAGE 1
Installation Instructions 1662 SERIES SHOWER SYSTEM KITS Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 M968637 Rev 2.
PAGE 2
INSTALL LOWER SUPPORT BRACKET VERTICAL C/L The SLIDE BAR works best when secured to the wall studs or cross brace using the WOOD SCREWS. If a mounting into the studs is not possible, use appropriate wall fasteners to provide secure installation. Mark a vertical center line in the location you wish to install the SLIDE BAR. NOTE: The height from the finished floor is optional. See rough-in drawing for suggested dimensions. Fig. A HORZ. C/L 1 Fig.
PAGE 3
6 INSTALL SLIDE BAR INTO MOUNTING BRACKETS Install the SLIDE BAR (1) back into the lower MOUNTING BRACKET (2). IMPORTANT: The slot at the bottom of the slide bar must face toward the wall. Rotate the slide bar until it locks into place and cannot be turned. Fig. A. 3, 4 5 SLIDE BAR TOP Push top COVER (3) and MOUNTING BRACKET (4) down onto top of SLIDE BAR (1). Fig. A. Tighten MOUNTING SCREW (5) with phillips screw driver to secure assembly to wall. Fig. B Fig. A Fig.
PAGE 4
SHOWER SYSTEM KITS MODEL NUMBER 1662 SERIES 1660500.XXX HAND SHOWER 1660550.XXX HAND SHOWER 1660502.XXX HAND SHOWER 1660628.XXX HAND SHOWER 1660505.XXX HAND SHOWER 1660741.XXX HAND SHOWER 1660638.XXX HAND SHOWER 1660609.YYY HAND SHOWER 1660143.XXX HAND SHOWER 1660843.XXX HAND SHOWER 1660743.XXX HAND SHOWER M962506-YYY0A SUPPORT BRACKET 8888037.