Installation Sheet

ManualsBrandsAmerican Standard ManualsShower FaucetsAmerican Standard Tub and Shower Trim Package with Multi Function Hand Shower, Slide Bar, Hose, and Valve Trims - Rough In Included

- 1 -

1-5/8" TO 3-1/4"

12"

OPTIONAL

OPTIONAL TO FINISHED

FLOOR USUALLY

BETWEEN 48" TO 54"

1/2" SUPPLIES

PLUG TUB

OUTLET

6" DIA.

FINISHED WALL

Universal Inlets / Outlets:

1/2" NOM Copper Sweat or 1/2" NPT

5-7/8"

1-1/4"

1/2"

1/2" NPT

1660766.002

(1.5 gpm)

1660767.002

(2.5 gpm)

3-5/16"

8-1/8"

1/2" NPSM

48"

1-5/8"

36"

37-1/2"

FINISHED

WALL

3-1/8" DIA.

OPTIONAL TO FINISHED FLOOR

USUALLY BETWEEN

36" 60"

3-1/8" DIA.

TOP OF TUB RIM

BOTTOM OF TUB

4-3/8" REF.

1/2" COPPER

1" MIN.

INSTALLATION

INSTRUCTIONS

1662SG.215

1662SG.225

Thank you for selecting American-Standard...the benchmark

of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly–please

read these instructions carefully before you begin.

Installation must conform to all local building codes.

COMMERCIAL SHOWER

SYSTEM KITS:

1.5 GPM & 2.5 GPM

Product names listed herein are trademarks of AS America, Inc.

ROUGHING-IN DIMENSIONS

Certied to comply with ANSI A112.18.1

Electric Drill

Torch

6mm (15/64")

Drill Bit

Pencil

Phillips Screwdriver

Hammer

Adjustable Wrench

10'

Pipe Wrench

Tubing Cutter

Tape

Measure

Sealing Tape

RECOMMENDED TOOLS & MATERIALS

M965665 Rev.1.0 (1/17)

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS COMMERCIAL SHOWER SYSTEM KITS: 1662SG.215 1662SG.225 1.5 GPM & 2.5 GPM Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly–please read these instructions carefully before you begin. Installation must conform to all local building codes. Certified to comply with ANSI A112.18.
PAGE 2
1 INSTALL THE R121SS VALVE BODY NOTE: REFER TO INSTALLATION INSTRUCTIONS (M965661) SUPPLIED WITH VALVE BODY FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION. IMPORTANT: When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread sealant or Teflon tape on threaded connections. n See Roughing-in diagram before starting.
PAGE 3
5 INSTALLATION INSTRUCTIONS n The GRAB BAR (1) works best when secured to the wall studs or cross brace using WOOD SCREWS. If mounting into the studs is not possible, use appropriate wall fasteners provided to secure the installation. n Mark a vertical center line in the location you wish to install the SLIDE BAR (1). NOTE: The height from the finished floor is optional. See rough-in drawing for suggested dimensions.
PAGE 4
6 INSTALL HOSE AND HAND SHOWER TEST SHOWER SYSTEM n Install SEAL (1) into COUPLING NUT (2). Connect COUPLING NUT (2) to WALL SUPPLY NIPPLE (3) and tighten. n INSTALL second SEAL (4) into SPRAY HOSE END (5) and connect HAND SHOWER (6) to SPRAY HOSE END (5). Hand tighten. n Turn on water supplies and check all fuctions of of the SHOWER SYSTEM KIT. Check for any leaks. 6 4 5 3 1 2 CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
PAGE 5
PRESSURE BALANCE TEMPERATURE/VOLUME CONTROL VALVE 051122-0070A SCREWDRIVER STOPS MODEL NUMBER R121SS 013205-0070A STOP VALVE O-RING M952100-0070A PRESSURE BALANCING UNI 023529-0070A CARTRIDGE 050145-0070A 1/2" SWEAT PLUG M961854-0070A FIXATION RING WITH SCREWS 023603-0070A CARTRIDGE SCREWS M961856-0020A ESCUTCHEON AND SCREWS 078016-0020A ESCUTCHEON SCREWS M907050-0020A ESCUTCHEON CAP SET COLONY SOFT VALVE TRIM M909606-0020A DECAL MODEL NUMBER 030126-0070A HANDLE SCREW KIT T675.
PAGE 6
36" SLIDE BAR 1660.236.002 3-FUNCTION HAND SHOWER 1660766.002 (1.5 gpm) 1660767.002 (2.5 gpm) M9641800020A SPRAY HOLDER ASSEMBLY WALL SUPPLY M964179-0070A MOUNTING KIT 8888.037.002 8888037.002 WALL SUPPLY M962520-0020A CHECK VALVE METAL HOSE 8888.035.002 030782-0020A HOSE KIT 022650-YYY0A DIVERTER SPOUT Appropriate finish code CHROME 002 HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Mon. - Fri. 8:00 a.m. to 8:00 p.m.