Installation Instructions

ManualsBrandsAmerican Standard ManualsOverflows & AccessoriesOverflow Cover and Drain Kit for Freestanding Tub in Legacy Bronze

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.

Local building codes vary by location. Observe all local plumbing and building codes.

Your new bath is shipped to you after careful inspection.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Plug Wrench

• Slip Joint Pliers

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

• Silicone Caulking

• Tub & Tile Caulk

BEFORE YOU BEGIN....

TOOLS:

TOOLS & MATERIALS MAY BE REQUIRED

MATERIALS:

KIT INCLUDES:

CHANGE OVERFLOW COVER

SAVE FOR FUTURE USE

INSTALLATION INSTRUCTIONS

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure

that your installation proceeds smoothly--please read these instructions carefully before you begin.

755143-100 Rev. A 10/16

DRAIN KIT

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

Model: 1680100.XXX FOR FREESTANDING TUB 2765, 2766, 2767

Remove 2 set screws on existing overflow cover using

supplied Allen wrench. (See Fig. 1)

Replace with overflow cover included in this kit. Use Allen

wrench to tighten 2 set screws. (See Fig. 2)

OVERFLOW COVER

DRAIN

ALLEN WRENCH

Fig. 1 Fig. 2

2 SET SCREWS

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS DRAIN KIT Model: 1680100.XXX FOR FREESTANDING TUB 2765, 2766, 2767 Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. BEFORE YOU BEGIN.... Local building codes vary by location. Observe all local plumbing and building codes. Your new bath is shipped to you after careful inspection.
PAGE 2
CHANGE THE DRAIN 1 3 Use a pipe wrench and plug wrench to loosen the drain nut in the bottom of the outside of the tub as shown in Fig. 3. Remove toe tap drain cover. Place the tub on it's side. Place the plug wrench inside the drain from the inside so that the pipe wrench does not turn. With the plug wrench in place unscrew the drain nut and remove it by turning the pipe wrench. From the inside of the tub remove the drain body. Install the replacement finish drain as shown in Fig. 4. Fig.
PAGE 3
INSTRUCCIONES DE INSTALACIÓN KIT DE DESAGÜE Modelo: T1680100.XXX PARA TINA INDEPENDIENTE 2765, 2766, 2767 ANTES DE COMENZAR... Los códigos de construcción varían de un lugar a otro. Respete todos los códigos locales de edificación y plomería. Su nueva tina se le envía tras una inspección cuidadosa. Para asegurar el placer y rendimiento máximo de este producto, siga las instrucciones y respete las advertencias. ! NOTA: Tenga mucho cuidado al manipular las superficies de la tina.
PAGE 4
CAMBIE EL DESAGÜE 1 3 Use una llave inglesa y una llave para bujías para aflojar la tuerca del desagüe en la parte inferior del exterior de la tina como se muestra en la fig. 3. Retire la tapa del desagüe accionado con el dedo del pie. Coloque la tina apoyada de costado. Coloque la llave de bujías dentro del desagüe desde adentro para que la llave para tubos no gire. Con llave de bujías en su lugar, desatornille la tuerca del desagüe y retírela girando la llave para tubos.
PAGE 5
INSTRUCTIONS D’INSTALLATION Les codes locaux varient en fonction des lieux. Renseignez-vous sur tous les codes de plomberie et codes de construction. Votre nouvelle baignoire vous sera expédiée après une inspection minutieuse. Pour profiter pleinement de ce produit, veuillez suivre les consignes et respecter les avertissements fournis. ! REMARQUE : Manipulez les surfaces de la baignoire avec une grande précaution. Utilisez uniquement des linges non abrasifs pour éviter les rayures.
PAGE 6
REMPLACEMENT DU RENVOI 1 3 Utilisez la clé à tuyau et la clé à bonde pour desserrer l’écrou de renvoi au fond de la partie extérieure de la baignoire, comme illustré dans la figure 3. Retirez le couvercle du renvoi Toe Tap. Placez la baignoire sur le côté. Placez la clé à bonde dans le renvoi à partir de l’intérieur aﬁn que la clé à tuyau ne puisse être tournée. Une fois la clé à bonde en place, dévissez l’écrou de renvoi et retirez-le en tournant la clé à tuyau.