Installation Guide

ManualsBrandsAmerican Standard ManualsFarmhouse/Apron Kitchen SinksPekoe Farmhouse/Apron-Front Mount Stainless Steel 30 in. Single Bowl Kitchen Sink

SAVE FOR FUTURE USE

791679-100 Rev. C 1/18

Adjustable Wrench

Channel Locks

Regular Screwdriver

Phillips Screwdriver

10'

Saber Saw

Pipe Wrench

Level

Tubing Cutter

Square

Tape Measure

Electric

Drill

1 2 3 4 5 6 7 8 9 10 11

1 2 3 4 5 6 7 8 9 10

11 12 13 14 15 16 17 18 19 20 21 22 23 24

Hacksaw

Sealant

RECOMMENDED TOOLS AND MATERIALS

ROUGH-IN

* NOTE: Dimensions may vary. Please use the actual size of the sink that you will be installing in order to determine the

cutout dimensions for your countertop.

CURVED APRON FRONT STAINLESS STEEL SINK

Flush Mount or Under Mount Sink

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of components.

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

OBSERVE LOCAL PLUMBING AND BUILDING CODES

Before installing the sink, inspect it for damage. DO NOT install a damaged unit.

Notify your American Standard distributor of any damage. Return sink in original packing.

Product names listed herein are trademarks of AS America, Inc.

(229 mm)

1-3/8"

(35 mm)

4-3/4"

(120 mm)

16-9/16"

(420 mm)

22"

(559 mm)

19-15/16"

(508 mm)

(203 mm)

30-1/4"

(768 mm)

33"

(838 mm)

(229 mm)

1-3/8"

(35 mm)

4-3/4"

(120 mm)

16-1/2"

(420 mm)

22"

(559 mm)

19-15/16"

(508 mm)

(203 mm)

27-1/4"

(692 mm)

30"

(762 mm)

33" SINK 30" SINK

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE CURVED APRON FRONT STAINLESS STEEL SINK Flush Mount or Under Mount Sink Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
MOUNTING OPTIONS Sink can accommodate any standard 3-1/2" (89mm) sink outlet drain. COUNTERTOP Flush Mount Installation * Under Mount Installation * REPLACEMENT USE When replacing an original unit be sure to shut off water supply before removing the lavatory or disconnecting water supply lines and drain fittings. Original supplies and shutoff valves should be replaced on installation.
PAGE 3
FLUSH MOUNT or UNDER MOUNT INSTALLATIONS 1 DETERMINE MOUNTING OPTIONS Determine if the sink will be flush mounted or under mounted. Next measure the actual size of the sink being installed to determine cabinet opening dimensions and support frame location. (Also reference rough-in for dimensions.) The cabinet opening should equal the maximum dimensions of the sink to ensure a minimum gap between the sink apron and the cabinet.
PAGE 4
2 SUPPORT FRAME Construct a support frame to fit inside the cabinet opening. Ensure you provide proper clearance for faucet, water supply lines, drain assembly, garbage disposal mounting system and the structural parts of the cabinet. Flush Mount Installation Note: Ensure to install the support frame so that the top rim of the sink, (when placed within the frame), will be level and flush with the top surface of the countertop, (when countertop is installed). See diagram 2A below.
PAGE 5
3 SINK INSTALLATION CAUTION: Sink is heavy. For personal safety, use extra person for assistance with installation. STEP 1. Carefully set the sink within the support frame and position in center of cabinet opening. If flush mounted ensure that the sink top rim surface is level and flush with the countertop top surface, (when countertop is installed reference Flush Mount Installation and 2A). If under mounted ensure that the sink top rim is level and flush with cabinet top surface.
PAGE 6
4B Installing Countertop - Under Mount Installation Under mount cutout opening is determined by cabinet opening and should be 1" (2.5mm ) smaller than the cabinet opening on the sides and from back of sink apron. Carefully cut out the countertop opening, opening must be adequately finished and sealed to prevent damage from water absorption. Note: Check dimensions on first page as a reference and measure the sink being installed.
PAGE 7
5B APPLY SEALANT For Under Mount Sinks: Carefully wipe clean the sink apron and top rim free from all debris. Ensure that the surface on underside of countertop cutout opening is smooth and free of debris. Under mount installation requires a generous bead of sealant around the sink top rim where sink and countertop underside will make contact. APPLY SEALANT ON TOP THREE SIDES OF RIM TOP OF CABINET 6 INSTALL COUNTERTOP Carefully position and install the countertop.
PAGE 8
MAINTENANCE FOR STAINLESS STEEL SINKS: To keep the original quality of your Stainless Steel Sink, we recommend regular cleaning. Use a mild liquid dish detergent and water to clean the product after use. Rinse carefully and dry. PLEASE HAVE THE FOLLOWING IN MIND: • Do not let water or other liquids dry on the product. Liquids that are left to dry leave a grey build-up stain on the steel. • Stainless steel can stand hard treatment, but sharp objects can easily scratch the surface.