Installation Guide

ManualsBrandsAmerican Standard ManualsBathSerin Petite Single Hole Single-Handle Mono-Block Bathroom Faucet with Speed Connect Drain in Polished Chrome

GROOVE

(FAUCET

BASE)

PUTTY

IF REQUIRED

M965363

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

MONOBLOCK LAVATORY FAUCET with

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

2064.131

SERIN

™

PETITE

COLLAR ON

MOUNTING NUT

Figure B

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the rst time, every time.

INSTALL FAUCET

Turn off hot and cold water

supplies before beginning.

CAUTION

Installation less ESCUTCHEON PLATE:

Seat SEAL (1) into under side of FAUCET BASE (2).

Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and

DRAIN CABLE ASSEMBLY (8) through the mounting hole

of lavatory or mounting surface. Fig. B.

From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),

pulling faucet to front of sink, so SUPPLIES (3) rests against

mounting hole. Before ﬁnal tightening, make sure collar on

MOUNTING NUT (6) is seated into RETAINING WASHER (5).

Fig. C .

Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)

to complete faucet mounting.

Fig. C.

Fig. B.

Fig. A.

Installation with ESCUTCHEON PLATE #2064101P: Note; Escutcheon plate

not included with ﬁtting and must be ordered separately. Apply a light bead of

plumbers putty to underside of ESCUTCHEON PLATE (8) if mounting surface is

uneven. Place ESCUTCHEON PLATE (8) onto sink or mounting surface.

Seat

SEAL (1) into under side of FAUCET BASE (2). Feed FAUCET SUPPLIES (3),

MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8) through

ESCUTCHEON

PLATE (9)

and mounting hole of lavatory or mounting surface. Fig. A.

GROOVE

(FAUCET

BASE)

MOUNTING

SURFACE

Summary of content (7 pages)

PAGE 1
Installation Instructions SERIN™ PETITE 2064.131 MONOBLOCK LAVATORY FAUCET with Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect Drain* Certified to comply with ANSI A112.18.1 • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 8 1-1/4” O.D. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 ON TEST INSTALLED FITTING OFF 1 COLD 4 With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. HOT Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). 3 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill Bidet with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Bidet. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
SERIN ™ PETITE MONOBLOCK LAVATORY FITTING MODEL NUMBER 2064.