Installation Instructions

ManualsBrandsAmerican Standard ManualsBathSerin Wall-Mount 1-Handle Low-Arc Bathroom Faucet with Valve Body and Grid Drain in Satin

M968918 Rev.1.4

Certiﬁed to comply with ASME A112.18.1M

U.S. Patent No. 5,819,789

Turn off hot and cold water

supplies before beginning.

CAUTION

Installation

Instructions

2064.461

ROUGHING-IN

DIMENSIONS

INSTALL VALVE BODY

Determine where the ﬁnished wall location will be. This measurement

is very important! Note: The rough-in measurement from the ﬁnished

wall is; 1" minimum and 2" maximum. This is a 1" tolerance. See

rough-in illustration above.

Secure FAUCET BODY (1) to cross brace of wall structure

at required height using two wood screws and and pipe brace.

Turn valve to off position. Turn hot and cold supplies on and

check ﬁtting connections for leaks .

Complete wall construction.

WOOD

SCREWS

WOOD SCREWS

and PIPE BRACE

CROSS BRACE

WALL STUDS

Connect HOT water supply to left VALVE inlet and COLD water

supply to right VALVE inlet. Use pipe sealant or Teﬂon tape for

all threaded connections. For sweat connections, do not make

sweat connections directly to valve body. Damage to seals and

and valve cartridge may occur. Remove all valve parts before

making sweat connections to valve body.

HOT

COLD

16"

Recommended Tools

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Pipe Wrench

Teflon Tape

Plumbers' Putty or

Caulking

SINGLE CONTROL WALL MOUNT FAUCET

IN-WALL LAVATORY FITTING

SERIN

™

2-1/8" D.

(54mm)

2" MAX. (51mm) MAX.

1-1/4" O.D.

(32mm) O.D.

HOT COLD

2" D.

(52mm)

2" MAX.

(50mm)

1" MIN.

(25mm)

FINISHED

WALL

FINISHED

WALL

2" D.

(52mm)

9-1/8"

(233mm)

1/2" NPT

INLETS

4-3/8"

(110mm)

2-1/16"

(52.5mm)

(50mm)

TYPICAL INSTALLATION

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Summary of content (4 pages)

PAGE 1
Installation Instructions 2064.461 SERIN™ SINGLE CONTROL WALL MOUNT FAUCET IN-WALL LAVATORY FITTING Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ASME A112.18.1M U.S. Patent No. 5,819,789 M968918 Rev.1.4 To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
PAGE 2
INSTALL WALL SPOUT 3 Remove PLASTER GUARDS (1, 1a) from VALVE BODY and SPOUT NIPPLE (2). APPLY SEALANT 1 Apply thread sealant to SPOUT NIPPLE (2). 2 Thread SPOUT MOUNT (3) onto SPOUT NIPPLE (2) using a 10mm Hex Wrench. Tighten completely. 10mm HEX WRENCH 1a 2a INSTALL WALL SPOUT Install SEAL (4) into SPOUT ESCUTCHEON (5). Place SPOUT ESCUTCHEON (5) with SEAL (4) onto SPOUT (6). Fig. A Push SPOUT (6) onto SPOUT MOUNT (3).
PAGE 3
6 TEST INSTALLED FAUCET Turn HANDLE to "off" position. Remove AERATOR (1) using TOOL (2) supplied. 1 Turn hot and cold water supplies on. Operate HANDLE to flush water lines thoroughly. Check spout connections for leaks. 2 Check all drain connections for leaks. Turn handle to OFF position. Replace AERATOR (1). 7 SERVICE CAUTION Turn off hot and cold water supplies before beginning. To remove or replace cartidge Turn valve to OFF position. Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).
PAGE 4
SERIN ™ SINGLE HANDLE WALL MOUNT LAVATORY FAUCET MODEL NUMBER 2064.