Specification

ManualsBrandsAmerican Standard ManualsBathContemporary Single-Handle Floor Mount Roman Tub Faucet in Polished Chrome

Recommended Tools

Channel Locks

Tubing CutterFlat Blade Screwdriver

Phillips Screwdriver

Adjustable Wrench

Pipe Wrench

Teﬂon Tape

Electric Drill

6mm

Hex wrench

5mm

Hex wrench

Level

ROUGHING-IN DIMENSIONS

2064.951

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

11-5/16"

(287mm)

1-7/8" DIA.

(48mm)

12˚

24" MAX.

(609mm)

35-1/8" MAX.

(892mm)

42" MAX.

(1067mm)

IMPORTANT

NOTICE TO THE INSTALLER!

Please check with your local Code Authority

for acceptable installation requirements for

this Roman Tub set with hand shower. Some

local codes may require a vacuum breaker

and/or a pressure balanced mixing valve to

be installed in conjunction with this product.

*Adequate ﬂoor support is required.

The wood support must be a minimum

of 2" (51mm) thick by 10" (254mm) wide.

2x6 lumber is NOTadequate for

this application.

(177mm)

47" MAX.

(1193mm)

LEVELING NUT

WASHER

LOCK WASHER

MOUNTING NUT

MOUNTING SCREW

26-15/16" MAX.

(684mm)

Contemporary Round

Floor Mounted Tub Filler

ESCUTCHEON

10" (254mm) MIN.

FLOOR JOIST

2-3/4"

70mm MIN.

1/2" NPT

FEMALE THREAD

COLD

1/2" NPT

FEMALE THREAD

HOT

FINISHED

FLOOR

FINISHED

FLOOR

4-3/4" x 4-3/4"

(120 x 120mm)

4" DIA.

(103mm)

*2" MIN.

(51 mm)

*WOOD SUPPORT

3/4"

(19mm)

PLASTER GUARD

Round Bubble Level

M965638 REV. 1.3 (10/15)

Summary of content (8 pages)

PAGE 1
Installation Instructions Contemporary Round Floor Mounted Tub Filler 2064.951 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
PAGE 2
1 INSTALL TUB FILLER FLOOR SUPPORT CAUTION Turn off hot and cold water supplies before beginning. • Note: Refer to Roughing-in Dimensions on page one for additional information. • Adequate floor support is required. The WOOD SUPPORT (1) must be a minimum of 2" (51mm) thick by 10" (254mm) wide. 2x6 lumber is NOT adequate for this application. • Locate WOOD SUPPORT (1) between floor joists keeping a minimum distance of 2-3/4" (70mm) from the top surface of wood support to the finished floor.
PAGE 3
INSTALL ROUGH-IN VALVE • Locate the position on the wood support where the ROUGH-IN VALVE (1) will be installed. Use the ROUGH-IN VALVE (1) as a guide to mark the four mounting hole locations. Fig. 1. • Remove ROUGH-IN VALVE (1) and drill four pilot holes of 3/8" (9mm) in diameter. Fig 2. • Install the 4 MOUNTING SCREWS (2) into wood support. • Install ROUGH-IN VALVE (1) onto the 4 MOUNTING SCREWS (2) and tighten NUTS & WASHERS (2) supplied. *Important: FRONT of ROUGH-IN VALVE (1) must face bath rim.
PAGE 4
5 FINISH FLOOR INSTALLATION • Complete the installation of the Finished Floor. Tile as close to the PLASTER GUARD (3) as you can. • Caulk between Finished Floor and PLASTER GUARD (3). 3 FINISHED FLOOR ROUGH FLOOR 1 FRON T HOT COLD 6 REMOVE EXPOSED PLASTER GUARD • Cut the exposed part of the PLASTER GUARD (3) flush with the finished floor. Be careful not not damage the floor. 3 FINISHED FLOOR 1 FRON T HOT COLD M965638 REV. 1.
PAGE 5
7 REMOVE RETAINING PLATE AND SCREWS • Remove the SIX RETAINING PLATE SCREWS (4) with a (5mm) hex wrench. • Remove RETAINING PLATE (5). 5mm HEX WRENCH 5 4 FINISHED FLOOR 1 FRONT COLD HOT 8 REMOVE HOT AND COLD TEST PLUGS Note: Floor is not shown for clarity in this illustration. • Remove the two TEST PLUGS (6) with a (6mm) hex wrench. 6mm HEX WRENCH 6 M965638 REV. 1.
PAGE 6
9 INSTALL TUB FILLER • Before final installation, check that all sealing surfaces are clean and that the INLET HOSE O-RINGS (7) are not damaged. Important: INLET HOSE O-RINGS (7) can be damaged if caution is not used when installing. 7 Match inlet hose marked with a blue dot with the hole on the manifold also marked with blue dot. (VIEW “A”) 8 (VIEW “A”) HOT COLD • Install the INLET HOSES (8) into the MANIFOLD MOUNTING BASE (9).
PAGE 7
9b INSTALL SPOUT AND HAND SHOWER • Align slot in RETAINING RING (13) with SET SCREW HOLE (14) in SPOUT (15). Install SPOUT (15) onto FAUCET BASE (16). Align SPOUT (15) with bath and tighten SET SCREW (17). (VIEW “B”) • Install SEALS (18) on both ends of the SPRAY HOSE (19). Connect the end with the hex to the DIVERTER (20) using an adjustable wrench. Hand tighten the connection to the HAND SHOWER (21). Note: When not in use, the HAND SHOWER (21) should be seated in the SHOWER HOLDER (22).
PAGE 8
Contemporary Round Floor Mounted Tub Filler MODEL NUMBER 2064.