Installation Guide

ManualsBrandsAmerican Standard ManualsBathtubsPrinceton 60-in White Porcelain Enameled Steel Oval In Rectangle Left-Hand Drain Alcove Bathtub

Observe Local Plumbing and Building Codes

FRAMING INSTRUCTIONS

SAVE FOR FUTURE USE

791174-400 Rev. M

Product names listed herein are trademarks of AS America, Inc.

Princeton™ Bath w/Integral Overflow Models:

2390.202.ICH, 2391.202.ICH, 2392.202.ICH, 2393.202.ICH,

2390.202.IPB, 2391.202.IPB, 2392.202.IPB, 2393.202.IPB,

2390.202.IBS, 2391.202.IBS, 2392.202.IBS, 2393.202.IBS

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require

professional help.) Also be sure your installation conforms to local codes.

Note recess is 1527 x 762mm (60-1/8 x 30). Cut a 229 x 305mm (9 x 12) hole in sub floor for drain, centered 362mm (14-1/4)

as shown for below floor rough. Locate studs as required, then ensure rough opening dimensions are proper and supports

are plumb and square.

Install stringer as shown (346mm [13-5/8] for through the floor drain or 435mm [17-1/8] for above the floor drain.)

1527mm

(60-1/8)

762mm

(30)

TUB WID

362mm

(14-1/4)

229 x 305mm

(9 x 12) FLOOR

CUTOUT

FOR DRAIN

762mm

(30)

IMPORTANT

The Drain Assembly is enclosed with tub models listed above.

Locate and retain for tub installation before discarding tub carton.

FULL LENGTH LEVELING SUPPORT

STRINGER 51 x 102mm (2 X 4 X 5 FT.)

APPLY BEAD OF SILICONE CAULKING

TO TOP OF LEVELING SUPPORT

STRINGER BEFORE INSTALLING TUB

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Princeton™ Bath w/Integral Overflow Models: 2390.202.ICH, 2391.202.ICH, 2392.202.ICH, 2393.202.ICH, 2390.202.IPB, 2391.202.IPB, 2392.202.IPB, 2393.202.IPB, 2390.202.IBS, 2391.202.IBS, 2392.202.IBS, 2393.202.IBS Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.
PAGE 2
DRAIN INSTALLATION 1 Remove Lift and Turn Stopper and Tailpiece Assembly from box and check that all parts are included. Remove Lift and Turn Stopper Assembly from Tailpiece by setting Stopper to closed position, and turning Stopper Knob counter-clockwise. (Re-install Stopper after Drain installation is completed.) 2 Apply plumbers putty around drain hole and pipe thread compound on threaded end of tailpiece. 3 Set Tailpiece in drain hole.
PAGE 3
INSTALLATION - BEDDING MATERIAL (MORTAR, SANDMIX, ETC.) IS ACCEPTABLE SUB FLOOR MUST BE STRUCTURALLY SOUND & FREE OF MOVEMENT / FLEXING The tub is provided with an integral base for easier installation. Position the bath on the floor and slide into place until the tub is resting on the rear stringer. The base does not need to contact the floor for proper installation. The base on the 2392 and 2393 models is raised above the floor to facilitate drain installation.
PAGE 4
5 ROUGHING-IN 1524mm (60) 48mm (1-7/8) FINISHED WALL 197mm (7-3/4) 362mm (14-1/4) 19mm (3/4) FULL LENGTH SUPPORT STRINGER 9 x 12 HOLE IN SUB-FLOOR OUTLINE OF SKID PATTERN 762mm (30) FINISHED WALL 89mm (3-1/2) PROVIDE FULL 346mm LENGTH SUPPORT (13-5/8) STRINGER AT THIS POINT BEDDING MATERIAL IS ACCEPTABLE 1-1/2 N.P.S.M.