Specifications

ManualsBrandsAmerican Standard ManualsDomestic Appliances2506.192

(In Toronto Area only: 1-905-3061093)

To l e a r n more a b o u t Amer i c a n S tandard Fa u c e t s v i s i t o u r website a t : www.us.amstd.com or U.S.

customer's e-mail us at:

sensor@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call

(855) 752-9259 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-3061093)

Installation Instructions

Certiﬁed to comply with ASME A112.18.1M

M965274 REV. 1.2

2506.192, 2506.195

SELECTRONIC®

Hard-Wired AC Powered Moments

Lavatory Proximity Faucet

PRODUCT NUMBERS

Product No.'s & Options

Speciﬁcations

How to Install

Electrical Hook-up

Maintenance

FAQ,s

Replacement Parts

2-3

4-5

6-7

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any

components will void the warranty.

Summary of content (9 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s SELECTRONIC® Hard-Wired AC Powered Moments Lavatory Proximity Faucet PRODUCT NUMBERS 2506.192, 2506.195 CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.'s & Options 1 Certified to comply with ASME A112.18.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions Fig. 1 GENERAL DESCRIPTION: FINISHED WALL 154mm (6-1/16) 159mm (6-1/4) Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on AC permanent power. Water pressure range from 20 to 125 psi. In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in checks, and flexible stainless steel 15" reach inlet hose for spout connection. 126mm (5) 55.
PAGE 4
2 MOUNT ENCLOSURE; Fig. 2 Fig. 2 1. Determine location of ENCLOSURE (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made. NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance between wall supply and ENCLOSURE (1) must be taken into consideration. LAVATORY RIM OR MOUNTING SURFACE 14" (356mm) SUPPLIES ENCLOSURE MOUNTING HOLES 1 2-3/4" (71mm) 2. Remove 4 screws from COVER (2) and pull off COVER (2).
PAGE 5
ELECTRICAL INSTALLATION Fig. 1 1 1 ELECTRICAL CONNECTIONS; Fig. 1 CAUTION Before opening ENCLOSURE turn off power from electrical box . NOTE: Make power supply connection before mounting ENCLOSURE (1) to wall. Fig. 1b. 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Feed the EXTENSION CABLES (2) from the Faucet through the top of ENCLOSURE (3). Fig. 1a. Fig. 1a Fig. 1b 2 3. Remove SPLIT PLUG (4) from POWER SUPPLY GROMMET (5). Insert POWER CORD (7) into SPLIT PLUG (4).
PAGE 6
Fig. 2 Unit #1 Unit #2 Unit #3 FAUCET WIRE CONNECTORS FAUCET WIRE CONNECTORS FAUCET WIRE CONNECTORS 10 ft. EXTENSION CABLE 6 10 ft. EXTENSION CABLE 6 9 5 6 9 5 8 8 ELECTRICAL BOX OR EQUIVALENT BY OTHERS 2 FOR HARD WIRED AC-POWERED Fig. 2a (MULTI HOOK-UP); Fig. 2, 2a, 2b Unit #1 2 SENSOR CABLES NOTE: Make power supply connection before mounting ENCLOSURE (1) to wall. Fig. 1b. 1a 6 1 1. Remove COVERS from all ENCLOSURES (2). Fig. 2. 2.
PAGE 7
MAINTENANCE Fig 1 DETECTION ZONE 1 HAND WASH SENSOR OPERATION; Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop Two seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on to off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone.
PAGE 8
4 HOW TO CLEAN FILTER; Fig. 4 CAUTION Fig.4 Before opening ENCLOSURE disconnect AC power supply. 1. Remove ENCLOSURE COVER. 7/16" SOCKET 2. Close SUPPLY STOP (1) with 4mm Hex wrench. Note: Keep water flowing out of faucet while shutting off. 3. Unthread STRAINER (2) using a 7/16" socket. 2 1 4. Pull out the STRAINER (2) and clean with an old toothbrush. Rinse thoroughly with water. 5. Install the STRAINER (2) back in its place and tighten with a 7/16" socket. Caution: do not over tighten strainer.
PAGE 9
M965274 REV. 1.