Installation Guide

ManualsBrandsAmerican Standard ManualsAlcove BathtubsTown Square S 60 in. Acrylic Right Drain Rectangular Alcove Bathtub in White

HIGH GLOSS ACRYLIC SURFACE

755503-100

ROUGH-IN INFORMATION:

TOWN SQUARE

S INTEGRAL

APRON TUB

2544102 / 2544202

ROUGH-IN INFORMATION:

2545 TOWN SQUARE

S INTEGRAL

APRON TUB

2545102 / 2545202

Your new bath is shipped to you after careful inspection.

To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.

BEFORE YOU BEGIN....

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

• Nails

• Plumber’s Putty

• Silicone Sealant

• 1 x 3 or 2 x 4 Stringers

• Drop Cloth

• Mortar Mix or Grout

TOOLS:

TOOLS & MATERIALS REQUIRED

MATERIALS:

SAVE FOR FUTURE USE

60 x 32 x 19 In.

(1524 x 813 x 483mm)

74 Lbs. (34 Kg)

502 Lbs.(228 Kg)

51 Gal. (194 L)

20-7/16 x 43-1/4 In. (519 x 1098mm)

25-13/16 x 53-1/4 In.(656 x 1353mm)

12-3/4 In. (324mm)

38 Lbs./Sq.Ft. (186 Kgs/Sq.m)

10.18

28.00

GENERAL SPECIFICATIONS FOR 2544102/202 TUB

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

)

16"

(406 mm)

18-11/16"

(475 mm)

STRINGER

HEIGHT

19"

(483 mm)

(25 mm)

3-1/2"

(89 mm)

(76 mm)

3-5/16"

(85 mm)

3-3/8"

(86 mm)

60"

(1524 mm)

10"

(254 mm)

3-3/16"

(81 mm)

32"

(813 mm)

TOWN SQUARE

S INTEGRAL APRON TUB

60x30" RHO 2545102 / LHO 2545202

60x32" RHO 2544102 / LHO 2544202

Local building codes vary by location. Observe all local plumbing and building codes.

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation

proceeds smoothly--please read these instructions carefully before you begin.

INSTALLATION INSTRUCTIONS

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.

15"

(381 mm)

18-11/16"

(475 mm)

STRINGER

HEIGHT

19"

(483 mm)

(25 mm)

3-1/2"

(89 mm)

(76 mm)

3-3/8"

(85 mm)

3-3/8"

(86 mm)

60"

(1524 mm)

10"

(254 mm)

3-3/16"

(81 mm)

30"

(762 mm)

60 x 30 x 19 In.

(1524 x 762 x 483mm)

70 Lbs. (32 Kg)

458 Lbs.(208 Kg)

47 Gal. (176 L)

18-7/16 x 43-1/4 In. (468 x 1098mm)

23-13/16 x 53-1/4 In.(605 x 1353mm)

12-3/4 In. (324mm)

37 Lbs./Sq.Ft. (179 Kgs/Sq.m)

10.18

26.39

GENERAL SPECIFICATIONS FOR 2545102/202 TUB

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

)

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS TOWN SQUARE® S INTEGRAL APRON TUB 60x30" RHO 2545102 / LHO 2545202 60x32" RHO 2544102 / LHO 2544202 HIGH GLOSS ACRYLIC SURFACE Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. BEFORE YOU BEGIN.... Your new bath is shipped to you after careful inspection.
PAGE 2
GENERAL INSTALLATION INFORMATION ... 1. When installing coordinating bath walls, additional studs may be required. Refer to those installation instructions prior to installing tub. 2. Bath walls are to be installed over stud walls. 3. Bath may only be installed in a recess or fold over edge type installation. 4. It is recommended that the 2544 and 2545 Town Square S Tub be set in a small bed of mortar or grout to compensate for uneven floors.
PAGE 3
2 Fig. 3 A.) THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. We recommend the use of mortar as bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and before it sets, position the bath within the recess until the rim is leveled against the leveling stringers (Fig. 3) shown below. The rim of the bath MUST NOT support weight.
PAGE 4
POST INSTALLATION CLEAN-UP Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.