Installation Guide

ManualsBrandsAmerican Standard ManualsBathTown Square 2-Handle Deck-Mount Roman Tub Faucet with Hand Shower in Polished Chrome

TOWNSQUARE

Certiﬁed to comply with ANSI A112.18.1M

ROUGHING-IN

DIMENSIONS

Required Tools

Wrench

(Supplied)

Turn off hot and cold water supplies before beginning.

CAUTION

Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.

Make sure that the RUBBER RING (2) is properly seated in RECESS

at base of SPOUT (3).

Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto

SHANK (1). From underside of ledge secure SPOUT (3) into position

with LOCKNUT (6).

SPOUT ASSEMBLY

PREPARE TUBE AND TEE ASSEMBLY

Prepare TUBE and TEE ASSEMBLY (1) to ﬁt center to center

VALVE (2) location (between 6-1/2" and12"). If necessary,

cut and/or bend TUBING carefully. Make sure tube bend is

close to the TEE (1) so that it will not effect the compression

joint at the VALVE CONNECTION.

Remove COUPLING NUT (3) and FERRULE (4) from each

VALVE (2) and slide onto TUBING (5).

Adjustable Wrench

Channel Locks

2555.900

2555.901

Flat Blade Screwdriver

VALVE inlet is 3/4-inch NPT male connector.

NOTE

ADJ. 6-1/2 TO 12

RECESS

MOUNTING

LEDGE.

MOUNTING

SURFACE

8-1/4

3-5/8

ADJ. 6-1/2 TO 12

1-1/2 MAX.

1-1/4

MAX.

1-3/16 D.

(H)

(C)

1-1/8 D.

3/4-14 MALE

N.P.T. INLETS

12 MAX

1-1/16 D.

Phillips Screwdriver

M968788 Rev. 1.2

DECK-MOUNT BATH FILLER

Installation

Instructions

Thank you for selecting American-Standard...the benchmark

of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Summary of content (3 pages)

PAGE 1
Installation Instructions TOWNSQUARE 2555.900 2555.901 DECK-MOUNT BATH FILLER Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M968788 Rev. 1.2 ROUGHING-IN DIMENSIONS Required Tools ADJ. 6-1/2 TO 12 8-1/4 Phillips Screwdriver MOUNTING SURFACE 3-5/8 Adjustable Wrench Flat Blade Screwdriver 1-1/4 MAX.
PAGE 2
3 VALVE ASSEMBLY Install LOCKNUTS (1) and RUBBER WASHERS (3) onto valve shanks. 10 Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5) into mounting holes from underside of ledge. DECK ADAPTER 11 Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is properly seated on SHANK (7). Push COUPLING (9 or 9a) into TEE (6) and attach to SPOUT SHANK (7) and tighten. Note: For product with Hand Shower, COUPLING (9) is tightened using a 10mm (3/8”) Hex Wrench.
PAGE 3
5 HANDSHOWER INSTALLATION (Model 2555.901 series only) 11 Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4) and LOCKNUT from underside of ledge. Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT. 1 Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple at the bottom of COUPLING (7). Tighten firmly.