Installation Guide

ManualsBrandsAmerican Standard ManualsWhirlpool Tubs2734.018.020

THANK YOU...

for selecting an American Standard bath. Your new bath is

shipped to you after careful inspection. The whirlpool version

is completely assembled with pump, motor, and system

piping. All you need to finish the installation are your

selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this

product, please follow the instructions and cautions.

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping

damage. If such damage is found, report it to your vendor

immediately. After inspection and during installation, protect

the bath from construction damage. Before installation,

and before enclosing with wallboard, tile, etc., the bath

must be filled with water and operated to check for leaks

that may have resulted from shipping damage or

mishandling! Do not make modifications to the whirlpool

system or remove pump from factory mounting. This could

adversely affect the safety and performance of the whirlpool

and void the warranty. Do not handle or move the whirlpool

by the pump, motor, or piping system. Fittings (bath filler,

shower arm, etc.) are not provided with the bath and must

be ordered separately. Framing and enclosing materials are

provided by others.

For electrical requirements, refer to section titled “Whirlpool

Electrical Installation Instructions”.

Check for availability of optional American Standard wall

tiling bead (required for recess installation).

Protect all finished surfaces of the whirlpool during

construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at

any time.

NOTE: Deck-mounted fittings are not recommended.

752690-100 Rev. E

All product names listed herein are trademarks

of AS America Inc. unless otherwise noted.

List of Optional Components (not included):

• Tile Bead Kit - 751755-100

• Apron Kit (see your American Standard Distributor)

List of Required Components (not included):

• Drain (see your American Standard Distributor)

• Bath Filler (see your American Standard Distributor)

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x 4 Stringers

• Drop Cloth

• 15 amp GFI Outlet

• Cement, Plaster, Grout

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

60 x 32 x 19-3/4 In. (1524 x 813 x 502mm)

87 Lbs. (39 Kg.)

554 Lbs. (249 Kg.)

56 Gal. (212 L)

40 Gal.(152 L)

44 x 21 In. (1118 x 533mm)

55 x 26 In. (1397 x 660mm)

13-1/2 In. (343mm)

42 Lbs./Sq.Ft. (201 Kgs/Sq.m)

10.2

26.6

GENERAL SPECIFICATIONS FOR 2734 WHIRLPOOL

5.5 AMPS,115V.

WHIRLPOOL ELECTRICAL SPECIFICATIONS

SYSTEM I PUMP

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

WHIRLPOOL MIN. OPERATING VOL.

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

)

1524mm

(60)

210mm

(8-1/4)

813mm

(32)

44mm

(1-3/4)

DRAIN OUTLET

PROVIDE ACCESS TO PUMP FOR

SERVICING ON ALL INSTALLATIONS

OUTLINE OF CUTOUT

1486x775mm

(58-1/2 X 30-1/2)

406mm

(16)

98mm

(3-7/8)

35mm

(1-3/8)

38mm

(1-1/2)

89mm

(3-1/2)

1-1/2 N.P.T.M. THREADS

1-1/2 O.D. TAILPIECE

464mm

(18-1/4)

BATH

SUPPORT

MATERIAL

502mm

(19-3/4)

ROUGH

FLOOR

LEVELING STRINGER

(NOT FOR SUPPORT)

ON/OFF

SWITCH

CUTOUT IN FLOOR FOR DRAIN

305mm

(12)

229mm

(9)

PUMP

DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY

VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED

BY ANSI STANDARDS Z124.1 AND A112.19.7.

2734 SERIES WHIRLPOOL/BATHING POOL

MAINSTREAM

HIGH GLOSS ACRYLIC

INSTALLATION INSTRUCTIONS

Summary of content (4 pages)

PAGE 1
MAINSTREAM® HIGH GLOSS ACRYLIC INSTALLATION INSTRUCTIONS 2734 SERIES WHIRLPOOL/BATHING POOL THANK YOU... PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS 1524mm (60) 210mm (8-1/4) for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.
PAGE 2
INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for access to the drain components. NOTE: The apron should not be used as the primary access opening. 1.
PAGE 3
ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3.
PAGE 4
DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings are factory tightened and inspected, some loosening may have occured during transit.