Installation Guide

ManualsBrandsAmerican Standard ManualsBathCadet 5.5 ft. Acrylic Flatbottom Non-Whirlpool Less Tub Filler Bathtub in Arctic White with Satin Nickel Drain

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.

Local building codes vary by location. Observe all local plumbing and building codes.

Your new bath is shipped to you after careful inspection.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

• Screws

• Silicone Caulking

BEFORE YOU BEGIN....

TOOLS:

TOOLS & MATERIALS REQUIRED

MATERIALS:

ROUGH-IN INFORMATION:

FREESTANDING TUB

66 x 32 x 23 In. (TUB ONLY)

(1676 x 813 x 584mm)

120 Lbs. (54 Kg)

600 Lbs.(272 Kg)

58 Gal. (220 L)

47.25 x 20.5 In. (1200 x 521mm)

56.25 X 23.25 In.(1429 x 591mm)

14.625 In. (371mm)

79 Lbs./Sq.Ft. (386 Kgs/Sq.m)

GENERAL SPECIFICATIONS FOR

2764 SERIES TUBS

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

21-1/2"

(546mm)

1-1/2"

(38mm)

1" (25mm)

FROM INSIDE

EDGE OF COVER

10"

(254mm)

5-5/8"

(143mm)

4-1/16"

(103mm)

43-1/8"

(1095mm)

64-5/8"

(1641mm)

30-5/8"

(778mm)

FLOOR

CUTOUT

COVER

FILLER LOCATION

DRAIN OVERFLOW

SAVE FOR FUTURE USE

FREESTANDING TUB

2764 SERIES

INSTALLATION INSTRUCTIONS

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation

proceeds smoothly--please read these instructions carefully before you begin.

754782-100 Rev. C

HIGH GLOSS ACRYLIC SURFACE

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FREESTANDING TUB HIGH GLOSS ACRYLIC SURFACE 2764 SERIES Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. BEFORE YOU BEGIN.... Local building codes vary by location. Observe all local plumbing and building codes. Your new bath is shipped to you after careful inspection.
PAGE 2
1 INSTALLATION INSTRUCTIONS: A.) Set up the cover in the desired location. Locate the drain outlet location and supply line locations for the faucet (see faucet instructions). B.) Recommend cutting floor cutout - 10" x 5-5/8" (254mm x 143mm) use cover as guide, as shown above. C.) Mark lines on the floor for the cover location. Use these to relocate cover. D.) Turn the cover over and apply silicone caulking to the bottom of the cover as shown. 2 SCREW HERE A.
PAGE 3
5 A.) Tighten drain connections through access panel and install faucet per instructions included. 6 A.) Push drain access panel in place. POST INSTALLATION CLEAN-UP Remove all construction debris from bath. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water.
PAGE 4
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this bathing pool – American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser. To activate this limited warranty, the purchaser must go online to our website at www.americanstandard-us.