Installation Guide

ManualsBrandsAmerican Standard ManualsBathtub Faucets2764951.002

Teﬂon Tape

ROUGHING-IN DIMENSIONS

43-1/16"

(1094mm)

27-3/4"

(705mm)

38-3/16"

(970mm)

FINISHED WALL

16-3/4"

(426mm)

25-1/2"

(650mm)

1-1/4"

(32mm)

8-1/8"

(206mm)

2" DIA.

(50mm)

1/2" SUPPLIES

(13mm)

1/2"-14 NPT(13mm)

SUPPLY INLETS

“T”-CONNECTOR

HOT

COLD

FINISHED

FLOOR

4-3/4" DIA.

(120mm)

2764.951

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

M 9 6 5 14 0 R E V. 1. 1

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Recommended Tools

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Tubing Cutter

CLEAN FREESTANDING

SINGLE CONTROL BATH FILLER

Phillips Screwdriver

Pipe Wrench

1-1/4" Hole Saw

Electric Drill

Summary of content (6 pages)

PAGE 1
Installation Instructions 2764.951 CLEAN FREESTANDING SINGLE CONTROL BATH FILLER Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. ROUGHING-IN DIMENSIONS FINISHED WALL 8-1/8" (206mm) 43-1/16" (1094mm) Certified to comply with ANSI A112.18.1 M 9 6 5 14 0 R E V. 1. 1 27-3/4" (705mm) 38-3/16" (970mm) Recommended Tools 25-1/2" (650mm) 2" DIA.
PAGE 2
1 2 INSTALL SUPPLY HOSES AND RISER TUBES TO VALVE BODY CAUTION Turn off hot and cold water supplies before beginning. INSTALL BATH SPOUT AND HANDLE TO TUB FILLER Install SPOUT (1) into faucet body. Make sure O-RING (2) is installed and not damaged. Thread Hot and Cold SUPPLY HOSES (5) into MANIFOLD using a wrench or adjustable wrench. Make sure the connections are tight. Use Red tape (not supplied) to indicate the Hot SUPPLY HOSE. SEE VIEW “A” Hand tighten SPOUT NUT (3).
PAGE 3
DETERMINE MOUNTING LOCATION FIGURE 1. Determine the distance from the finished wall to the center of the floor water supply holes and mark a centerline. Note: Check that floor is level in both directions. Drill a 2" (51mm) diameter hole for the 1/2" Hot and Cold supplies. Slide MOUNTING FLANGE (1) downwards on the TUB FILLER ASSEMBLY (2). 2 Place MOUNTING FLANGE (1) over the floor supply hole. Align and center the TUB FILLER ASSEMBLY (2).
PAGE 4
INSTALL TUB FILLER ASSEMBLY FIGURE 1 INSTALL WATER SUPPLIES AND “T” ADAPTER FIGURE 1: Make sure FLEXIBLE HOT and COLD WATER SUPPLIES protrude through the 2" (51mm) diameter hole in the floor enough to make the supply connections to the “T” ADAPTER (4). FINISHED FLOOR HOT HOT 1-1/4" (32mm) COLD SUB-FLOOR 1/2" SUPPLIES (13mm) FIGURE 2: Hold the TUB FILLER ASSEMBLY (1) in place and install the three MOUNTING SCREWS (2). 1 Check aligment and level before fully tightening the MOUNTING SCREWS (2).
PAGE 5
INSTALL HAND SHOWER Install SEALS (1) on both ends of the SPRAY HOSE (2) and connect the one end with the hex nut to the TUB FILLER ASSEMBLY (3) using an adjustable wrench. Hand tighten the connection to the HAND SHOWER (4). Note: When not in use, the HAND SHOWER (4) should be seated in the HOLDER (5). 7 4 3 1 1 HEX NUT 8 5 2 6 6 TEST INSTALLED FAUCET Move HANDLE (6) into “off” position and remove AERATOR (7). Turn on water supplies and check all connections for leaks.
PAGE 6
CLEAN FREESTANDING SINGLE CONTROL BATH FILLER MODEL NUMBERS 2764.591 M964071-0020A HAND SPRAY M964060-0020A AERATOR ASSEMBLY M964072-0020A DIVERTER ASSEMBLY M964070-0020A HAND SPRAY HOSE KIT M964067-0020A HANDLE KIT M964114-0070A SUPPLYHOSES M964073-0070A CARTRIDGE M964069-0070A SCREW & ANCHOR KIT HOT LINE FOR HELP M964068-0070A T-CONNECTOR ASSEMBLY For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m.