Installation Guide

ManualsBrandsAmerican Standard ManualsBathSedona Loft 62.75 in. Acrylic Flatbottom Non-Whirlpool Bathtub in White

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.

Local building codes vary by location. Observe all local plumbing and building codes.

Your new bath is shipped to you after careful inspection.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

• Silicone Caulking

• Tub & Tile Caulk

BEFORE YOU BEGIN....

TOOLS:

TOOLS & MATERIALS REQUIRED

MATERIALS:

ROUGH-IN INFORMATION:

FREESTANDING TUB

Model 2766

SAVE FOR FUTURE USE

INSTALLATION INSTRUCTIONS

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure

that your installation proceeds smoothly--please read these instructions carefully before you begin.

755021-100 Rev. C

FREESTANDING TUB

HIGH GLOSS ACRYLIC SURFACE

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

Note: An access panel

must be provided to

facilitate the connection

of the drain to the

drain/waste outlet.

Access must be made

through the floor below

the tub.

62-3/4"

(1595 mm)

DRAIN OVERFLOW

29-7/8"

(760 mm)

22-7/8"

(580 mm)

16-1/8"

(410 mm)

2-3/4"

(70 mm)

5-1/8"

(130 mm)

ø2-1/8"

(ø55 mm)

62-3/4 x 29-7/8 x 22-7/8 in.

(1594 x 759 x 581mm)

103 Lbs. (47 Kg.)

605 Lbs. (274 Kg.)

72 Gal. (273 L)

45-1/4 x 20-1/2 In. (1149 x 521mm)

60 x 27-1/8 In. (1524 x 689mm)

13-3/8 In. (340mm)

47 Lbs./Sq.Ft. (227 Kgs./Sq.m)

GENERAL SPECIFICATIONS FOR

2766 FREE STANDING BATH

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

Models: 2765, 2766, 2767

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FREESTANDING TUB HIGH GLOSS ACRYLIC SURFACE Models: 2765, 2766, 2767 Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. BEFORE YOU BEGIN.... Local building codes vary by location. Observe all local plumbing and building codes. Your new bath is shipped to you after careful inspection.
PAGE 2
ROUGH-IN INFORMATION: FREESTANDING TUB Model 2765 68-3/4" (1745 mm) 31-1/4" (795 mm) ø2-1/8" (ø55 mm) 5-1/8" (130 mm) 16-7/8" (430 mm) 2-3/4" (70 mm) 23-5/8" (600 mm) GENERAL SPECIFICATIONS FOR 2765 FREE STANDING BATH 68-3/4 x 31-1/4 x 23-5/8 in. INSTALLED SIZE (1746 x 794 x 600mm) 97 Lbs. (44 Kg.) WEIGHT 594 Lbs. (270 Kg.) WEIGHT w/WATER 71 Gal. (269 L) GAL. TO OVERFLOW 46-1/8 x 20-1/8 In. (1172 x 511mm) BATHING WELL AT SUMP 66 x 28-1/2 In. (1677 x 724mm) BATHING WELL AT RIM 14-1/8 In.
PAGE 3
ROUGH-IN INFORMATION: FREESTANDING TUB Model 2767 69-5/8" (1768 mm) 3-1/8" (80 mm) 11" (280 mm) 4-3/8" (110 mm) ø2-1/8" (ø55 mm) 31-3/4" (805 mm) 5-1/8" (130 mm) 3-1/8" (80 mm) 17-3/8" (440 mm) 23-5/8" (600 mm) GENERAL SPECIFICATIONS FOR 2767 FREE STANDING BATH 69-5/8 x 31-3/4 x 23-5/8 in. (1768 x 806 x 600mm) 112 Lbs. (51 Kg.) WEIGHT 484 Lbs. (220 Kg.) WEIGHT w/WATER 58 Gal. (220 L) GAL. TO OVERFLOW 44-7/8 x 16 In. (1140 x 406mm) BATHING WELL AT SUMP 63-3/8 x 25-1/2 In.
PAGE 4
1 INSTALLATION INSTRUCTIONS: Place the tub on a finished, level floor in the desired location. Using an erasable pencil or marker, trace the outline of the base of the tub on the floor. (See Fig. 1) FIG. 1 2 Using the adjustable feet on the underside of the tub, ensure that the tub is level. Ensure that there is a gap between the tub base and the floor. Gap shall not exceed 3/16" (5mm). (See Fig. 2) 3/16" MAX (5mm) FINISHED FLOOR 3 FIG. 2 Remove the tub.
PAGE 5
Apply a generous bead of silicone caulking to the base of the tub including the cross-braces. (See Fig. 5) FIG. 5 Carefully set the tub into position. Ensure that drain strainer gasket is fully seated against the tail piece flange. Connect the tailpiece to the tub drain. Tighten all of the drain connections. Remove any excess caulking where the tub meets the floor. 6 7 Note: Connecting the tailpiece assembly and the drain will require access from beneath the tub. Fill the tub with water and drain.
PAGE 6
AS AMERICA, INC. LIMITED LIFETIME WARRANTY FOR TUBS AND SHOWER BASES AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this tub/shower base – American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser. To activate this limited warranty, the purchaser must go online to our website at www.americanstandard-us.