Specification

H56
© 2007 American Standard Inc.
464 mm
(18-1/4)
38mm
(1-1/2)
502mm
(19-3/4)
1-1/2 O.D.TAILPIECE
LEVELING
STRINGER
NOT FOR
SUPPORT
ROUGH
FLOOR
89mm
(3-1/2)
305mm
(12)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
C/L OF
OVERFLOW
102mm
(4)
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
70 mm
(2-3/4)
117 mm
(4-5/8)
1-1/2 N.P.T.M.
THREADS
C/L OF DRAIN
INTEGRAL
SUPPORT
FEET
SAFE-T-HEATER
REMOVABLE
BLANK
RECOMMENDED FITTING LOCATION
64 X 330mm (2-1/2 x 13")
FOR PIER OR ISLAND
INSTALLATIONS ONLY
ALT. FITTING
LOCATION #1
1829 mm
(72)
1067mm
(42)
OUTLINE OF CUTOUT
1791mm x 1029mm
(70-1/2 X 40-1/2)
533mm
(21)
229mm
(9)
305 mm
(12)
57mm
(2-1/4)
(8) JETS
CUTOUT IN FLOOR
FOR DRAIN
PUMP
FINISHED
WALL
19 mm
(3/4)
229 mm
(9)
(2) AIR VALVES
PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS
RECOMMENDED FITTING LOCATION
76 X 330mm (3 x 13")
FOR PIER OR ISLAND
INSTALLATIONS ONLY
ALT. FITTING
LOCATION
1829 mm
(72)
1067mm
(42)
OUTLINE OF CUTOUT
1784 mm x 1022mm
(70-1/4 X 40-1/4)
533mm
(21)
464 mm
(18-1/4)
38 mm
(1-1/2)
502 mm
(19-3/4)
1-1/2 O.D.TAILPIECE
INTEGRAL
FEET
LEVELING STRINGER
NOT FOR SUPPORT
ROUGH
FLOOR
229mm
(9)
305 mm
(12)
57mm
(2-1/4)
89mm
(3-1/2)
CUTOUT IN FLOOR
FOR DRAIN
FINISHED
WALL
305 mm
(12)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
C/L OF
OVERFLOW
102 mm
(4)
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
70 mm
(2-3/4)
117 mm
(4-5/8)
1-1/2 N.P.T.M.
THREADS
19 mm
(3/4)
229 mm
(9)
C/L OF
SUPPLIES
C/L OF DRAIN
SEE FITTING
SPECS FOR
DIMENSIONS
72 x 42 x 19-3/4 In. (1829 x 1067 x 502mm)
137 Lbs. (62 Kg.)
821 Lbs. (372 Kg.)
82 Gal. (310 L.)
66 Gal. (256 L.)
50 x 27 In. (1270 mm x 686 mm)
65 x 33 In. (1651 x 838mm)
13 In. (330 mm)
42 Lbs./Sq. Ft. (203 Kgs/Sq. m.)
27.8
55.5
GENERAL SPECIFICATIONS FOR 2774 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIn. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
2.1 HP, 14.4 AMPS, 120V.SYSTEM I PUMP
72 x 42 x 19-3/4 In.
(1829mm x 1067 mm x 502mm)
112 Lbs. (50 Kg.)
795 Lbs. (358 Kg.)
82 Gal. (311 l.)
50 x 27 In. (1270 mm x 686 mm)
66 x 33 In. (1676 x 838mm)
13 In. (330 mm)
41 Lbs./Sq. Ft. (197 Kgs/Sq. m.)
27.8
55.5
GENERAL SPECIFICATIONS FOR 2774 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF
BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3 WALL TILING BEAD. KIT AND APRON NO. 9272.018 OR 9372.018 AVAILABLE AND MUST BE ORDERED SEPARATELY.
● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of  xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided lea et.
CADET™ 6' x 42"
WHIRLPOOL & BATHING POOL
HIGH GLOSS
Revised 10/07