Use and Care Guide

3
© 2009 AS America Inc.
TROPIC RIGHT HEIGHT™
ELONGATED ONE-PIECE TOILET
VITREOUS CHINA
TROPIC RIGHT HEIGHT™
ELONGATED ONE-PIECE TOILET
❑ 2786.016
• Vitreous china
• LXP (Luxury Performance) Toilet
• Low-consumption (6.0 Lpf/.6 gpf)
• Elongated siphon action bowl with
smooth-sided, concealed trapway
• PowerWash™ rim scrubs bowl with each ush
• 6-/2" rim height for accessible applications
• Fully glazed 2" trapway
• Oversized 3" ush valve with chemically
resistant apper
• Chrome trip lever
• 2 color-matched bolt hole covers
• Includes color-matched Duroplast Slow
Close Toilet Seat and cover with easy lift-off
feature for simple removal and reattachment
for cleaning
• 00% factory ush tested
• Transitional design coordinates with
Tropic lavatories and faucets
• 0 year warranty on entire toilet
Nominal Dimensions:
756 x 424 x 778mm
(29-3/4" x 6-3/4" x 30-/2")
Fixture only, supply by others
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A2.9.2-2008 / CSA B45.-08
• Los Angeles Department of Water and Power
Supplementary Purchase Specication For
Non-Adjustability
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
29-3/4"
(756 mm)
8-1/8"
(206 mm)
3/4"
(19 mm)
18-1/2"
(470 mm)
3-1/2"
(88 mm)
8-1/2"
(217 mm)
13-1/2"
(345 mm)
14"
(354 mm)
16-3/4"
(424 mm)
30-1/2"
(778 mm)
16-1/2"
(419 mm)
12"
(305 mm)
C/L OF OUTLET AND
TOILET MTG BOLTS
FINISHED WALL
IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.
FINISHED
FLOOR
2-7/8" (74mm)
5-1/2"
(140mm)
SUPPLY AS
REQUIRED
(position 2)
SUPPLY AS
REQUIRED
(position 1)
6"
(152mm)
3-3/4"
(95mm)
9"
(229mm)
14"
(355 mm)
OR
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES-CHECK LOCAL CODES.
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF
305MM (2") FROM FINISHED WALL TO C/L OF OUTLET.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE
ORDERED SEPARATELY.
*
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerance established by ANSI Standard A2.9.2
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
To Be Specied:
❑ Color:
❏ White ❏ Bone ❏ Linen
❑ Supply with Stop:
7/09