Installation Sheet

ManualsBrandsAmerican Standard ManualsBathTown Square S 1-Piece 1.28 GPF Single Flush Elongated Toilet in White, Seat Included

7301450-100 Rev. 2 (3/19)

Product names listed herein are trademarks of AS America, Inc.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife

Closet Bolts

Regular Screwdriver

Wax Ring/Gasket

Adjustable Wrench

Flexible Supply Tube

Sealant

Hacksaw

Carpenters Level

Tape Measure

ROUGHING-IN DIMENSIONS:

REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

BOULEVARD

- 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2891 - Elongated Right Height

with Seat

TROPIC

- 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2786 - Elongated Right Height

with Seat

TOWN SQUARE

- 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2847 - Elongated Right Height

with Seat

TOWN SQUARE

S - 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2851A - Elongated Right Height

with Seat

Model 2786 - TROPIC 1.28 gpf/ 4.8 Lpf

Model 2891 - BOULEVARD 1.28 gpf/ 4.8 Lpf

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

Thank you for selecting American Standard – the benchmark of fine quality for over 140 years. To ensure this product is installed properly, please read

these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONS

NOTE: Distance from wall to closet flange centerline must be as listed below:

C/L OF SEAT POST

HOLES 5-1/2"

(140mm) CENTERS

29-3/4"

(756 mm)

8-1/8"

(206 mm)

3/4"

(19 mm)

18-1/2"

(470 mm)

3-1/2"

(88 mm)

8-1/2"

(217 mm)

13-1/2"

(345 mm)

14"

(354 mm)

16-3/4"

(424 mm)

30-1/2"

(778 mm)

16-1/2"

(419 mm)

12"

(305 mm)

C/L OF OUTLET AND

TOILET MTG BOLTS

FINISHED WALL

IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).

First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.

The second suggested position is next to the toilet. Between these two positions, the space for the supply

between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.

IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).

First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.

The second suggested position is next to the toilet. Between these two positions, the space for the supply

between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.

FINISHED

FLOOR

2-7/8"

(74mm)

5-1/2"

(140mm)

SUPPLY AS

REQUIRED

(position 2)

SUPPLY AS

REQUIRED

(position 1)

(152mm)

3-3/4"

(95mm)

(229mm)

14"

(355 mm)

29-3/4"

(756 mm)

7-1/2"

(192 mm)

3/4"

(19 mm)

18-1/2"

(470 mm)

16-1/2"

(419 mm)

14-1/2"

(368 mm)

30-1/2"

(778 mm)

13-1/2"

(345 mm)

14-1/4"

(364 mm)

8-1/2"

(217 mm)

12"

(305 mm)

C/L OF SEAT POST

HOLES 5-1/2"

(140mm) CENTERS

FINISHED WALL

3-3/8"

(86mm)

3-1/4"

(83mm)

SUPPLY

REQUIRED

(position 1 or

position 2)

(152mm)

5-1/2"

(140mm)

3-3/4"

(95mm)

(229mm)

14"

(350 mm)

FINISHED

FLOOR

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS BOULEVARD® - 1.28 gpf/4.8 Lpf One-Piece Toilet Model 2891 - Elongated Right Height® with Seat TROPIC® - 1.28 gpf/4.8 Lpf One-Piece Toilet Model 2786 - Elongated Right Height® with Seat TOWN SQUARE® - 1.28 gpf/4.8 Lpf One-Piece Toilet Model 2847 - Elongated Right Height® with Seat TOWN SQUARE® S - 1.28 gpf/4.8 Lpf One-Piece Toilet Model 2851A - Elongated Right Height® with Seat Thank you for selecting American Standard – the benchmark of fine quality for over 140 years.
PAGE 2
a ROUGHING-IN DIMENSIONS: NOTE: Distance from wall to closet flange centerline must be as listed below: Model 2847 - TOWN SQUARE 1.28 gpf/ 4.8 Lpf Model 2851A - TOWN SQUARE S 1.28 gpf /4.
PAGE 3
7 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. 8a Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
PAGE 4
12 TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 12. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: LIFT ARM FIRST • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided. • The flush valve is leaking because it's worn, dirty or misaligned with tank ball or flapper (replace with a new flapper).
PAGE 5
INSTRUCCIONES DE INSTALACIÓN Inodoro de una pieza BOULEVARD® 1.28 gpf/4.8 Lpf Inodoro alargado Modelo 2891 Right Height® con asiento Inodoro de una pieza TROPIC® 1.28 gpf/4.8 Lpf Inodoro alargado Modelo 2786 Right Height® con asiento Inodoro de una pieza TOWN SQUARE® 1.28 gpf/4.8 Lpf Inodoro alargado Modelo 2847 Right Height® con asiento Inodoro de una pieza TOWN SQUARE® S 1.28 gpf/4.
PAGE 6
2a DIMENSIONES DE INSTALACIÓN: NOTA: La distancia desde la pared a la línea central de la brida de retrete debe ser la que se indica a continuación: Modelo 2847 - TOWN SQUARE 1,28 gpf/ 4.
PAGE 7
INSTALACIÓN DEL ASIENTO DEL INODORO Instale el asiento del inodoro según las instrucciones del fabricante. 8a Antes de continuar, identifique el tipo de conexión de suministro de agua que utiliza de acuerdo con al diagrama que aparece más adelante y utilice las piezas de montaje adecuadas para volver a conectar el suministro de agua de manera correcta. NO emplee masilla de plomero para sellar estas conexiones.
PAGE 8
12 SOLUCIÓN DE PROBLEMAS SI LA VÁLVULA DE SUMINISTRO SE CIERRA PERO SIGUE PERDIENDO AGUA POCO A POCO, repita el Paso 12. SI LA VÁLVULA DE SUMINISTRO SE CIERRA Y ABRE CUANDO NO SE USA, es señal de desperdicio de agua a causa de que: ELEVAR BRAZO PRIMERO • El extremo del tubo de carga está introducido en el tubo de rebose, debajo del nivel de agua del tanque. Fije el tubo de carga al de rebose con el sujetador en "S" suministrado.
PAGE 9
INSTRUCTIONS D'INSTALLATION Toilette monobloc BOULEVARD - 1,28 gpp/4,8 Lpp Modèle 2891-Allongé Right Height avec siège MD MD Toilette monobloc TROPIC - 1,28 gpp/4,8 Lpp Modèle 2786-Allongé Right Height avec siège MD MD Toilette monobloc TOWN SQUARE Modèle 2847-Allongé Right Height Toilette monobloc TOWN SQUARE Modèle 2851-Allongé Right Height MD MD MD MD - 1,28 gpp/4,8 Lpp avec siège S - 1,28 gpp/4,8 Lpp avec siège Nous vous remercions d'avoir choisi American Standard - synonyme de qualité supérie
PAGE 10
2a MESURES RELATIVES AUX POINTS DE RACCORDEMENT : REMARQUE : La distance entre le mur et la ligne médiane de la collerette de la toilette doit être comme suit : Modèle 2847 - TOWN SQUARE 1,28 gpp/ 4,8 Lpp Modèle 2851 - TOWN SQUARE S 1,28 gpp/4,8 Lpp 15-1/8 po (384 mm) 7/8 po (22 mm) L/C DE TROUS DE TIGE DE SIÈGES 5 1/2 po (140 mm) CENTRE 3-1/2 po (88 mm) 9 po (229mm) 3-3/4 po (95mm) 30-9/16 po (776 mm) 14-5/8 po (373 mm) PLANCHER FINI 9 po (229mm) 3-3/4 po (95mm) 14-5/8 po (373 mm) 6 po (152mm
PAGE 11
7 INSTALLATION DU SIÈGE DE TOILETTE Installer le siège de toilette selon les instructions du fabricant. 8a Avant de poursuivre, en vous fiant au tableau ci-dessous, déterminez quel type de raccordement à l'alimentation de l'eau vous avez et utilisez les pièces appropriées requises pour effectuer le raccordement. NE PAS utiliser de mastic de plombier pour sceller ces raccords de plomberie.
PAGE 12
DÉPANNAGE SI LA VALVE DE REMPLISSAGE SE FERME, MAIS CONTINUE À FUIR, répéter l'étape 12. SOULEVER LE BRAS D'ABORD SI LA VALVE DE REMPLISSAGE S'OUVRE ET SE FERME MÊME LORSQU'ELLE N'EST PAS UTILISÉE, cela indique qu'il y a une fuite d'eau parce que : • L'extrémité du tuyau de remplissage est insérée dans le tuyau de trop-plein, sous le niveau d'eau dans le réservoir. Fixer le tuyau de remplissage au tuyau de trop-plein à l'aide du collier de serrage en « S » fourni.