Installation Guide

ManualsBrandsAmerican Standard ManualsCorner Shower Bases3232S-ST3.020

755089-100

Product names listed herein are trademarks of AS America Inc.

NOTE: READ INSTRUCTIONS COMPLETELY BEFORE PROCEEDING WITH INSTALLATION.

ROUGHING-INS:

ROUGHING-IN CONTINUED ON NEXT PAGE

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONS

Axis Acrylic Shower Bases

MODELS 3232S, 3636A, 3838N, 3838A & 4242N

SAVE FOR FUTURE USE

Certified to comply with CSA B-45.5-11/IAPMO Z124-2011

Model: 3232S.ST3 Square

Shower Base

Model: 3636A.ST3 Rounded

Shower Base

Model: 3838A.ST3 Rounded

Shower Base

Model: 3838N.ST3 Neo

Shower Base

32-3/4" ± 3/16"

(832 mm ± 5 mm)

32-3/4" ± 3/16"

(832 mm ± 5 mm)

12"

(305 mm)

12"

(305 mm)

5/16" NOM

(8 mm NOM)

3-1/4"

(83 mm)

34" ± 3/16"

(864 mm ± 5 mm)

34" ± 3/16"

(864 mm ± 5 mm)

12"

(305 mm)

36"

(914 mm)

36"

(914 mm)

12"

(305 mm)

5/16" NOM

(8 mm NOM)

3-1/4"

(83 mm)

3-1/4"

(83 mm)

38" ± 3/16"

(965 mm ± 5 mm)

38" ± 3/16"

(965 mm ± 5 mm)

12"

(305 mm)

12"

(305 mm)

16"

(406 mm)

16"

(406 mm)

5/16" NOM

(8 mm NOM)

20-1/4"

(514 mm)

20-1/4"

(514 mm)

12"

(305 mm)

12"

(305 mm)

38" ± 3/16"

(965 mm ± 5 mm)

38" ± 3/16"

(965 mm ± 5 mm)

5/16" NOM

(8 mm NOM)

3-1/4"

(83 mm)

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Axis Acrylic Shower Bases MODELS 3232S, 3636A, 3838N, 3838A & 4242N Certified to comply with CSA B-45.5-11/IAPMO Z124-2011 Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 2
1 ROUGHING-IN: CONTINUED FROM PREVIOUS PAGE Model: 4242N.ST3 Neo Shower Base Note: Variations in levelness of subfloor may require adjustment of waste pipe height. See product drawings on this page for the specified drain locations. 42" ± 3/16" (1067 mm ± 5 mm) 12" (305 mm) 12" (305 mm) Ensure the floor and stud walls are square and plumb. Provide a 5" x 5" (127mm x 127mm) opening in the floor for the drain (see Fig. A). The drain plug accommodates a 2" (51mm) PVC waste pipe.
PAGE 3
4 After the bedding material has been poured and before it sets, lower the shower base into position with the drain assembly sliding over the waste pipe as shown in Fig. D. It will be necessary to "rock" the shower base until the top of the tile flange aligns with the lines drawn in Step 3 on the stud walls. Make certain the apron is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in two directions (see Fig. E).
PAGE 4
AS America, Inc. Limited Lifetime Warranty for Shower Bases AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this shower base – American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser. To activate this limited warranty, the purchaser must go online to our website at www.americanstandard-us.