Installation Guide

ManualsBrandsAmerican Standard ManualsToilet Tanks4142.901.020

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: For proper operation the recommended working pressure is between 25 psi at valve when flushing and 80 psi static.

INSTALLATION INSTRUCTIONS

CADET 1.1 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS

- Model 2462.100 Cadet Elongated 15"

- Model 2467.100 Cadet Elongated 16-1/2" High Bowl

YORKVILLE 1.1 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS

- Model 2876.100 Yorkville Elongated 15"

- Model 2878.100 Yorkville Elongated 16-1/2" High Bowl

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require professional

help.) Also be sure your installation conforms to local codes.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

Closet Flange Set (Cadet Toilets) Neoprene or Graphite Felt Gasket (Yorkville Toilets)

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

7301276-100 Rev. A

Product names listed herein are trademarks of AS America, Inc.

2-2

3-2

2-1

3-1

DIMENSIONS (Nominal) NOTE: Distance from floor to closet

flange centerline (rough-in) must be 4" (102 mm) with flange

surface flush to 1/16" (16mm) max. beyond finished wall.

DIMENSIONS (Nominal) NOTE: Distance from wall to closet

flange centerline (rough-in) must be 12" (305 mm)

FOR CADET TOILETS: FOR YORKVILLE TOILETS:

FLUSH TO

1/16" (16mm)

EXPOSED

CLOSET

FLANGE

CLOSET

BOLTS

168mm

(6-5/8")

PILOT

HOLES

102mm

(4)

346mm

(13-5/8)

Install closet bolts in flange

channel, turn 90°, and slide

into place 6" (152 mm) apart

and parallel to floor. (Use

putty to hold bolts in place if

necessary.) Brace under

flooring as needed and

drill two mounting pilot

holes as shown.

INSTALL CLOSET BOLTS

Install closet bolts in flange

channel, turn 90°, and slide

into place 6" (152 mm)

apart and parallel to wall.

INSTALL CLOSET BOLTS

305mm

(12)

CLOSET FLANGE

CLOSET BOLTS

29-3/4"

(752mm)

18-1/2"

(470mm)

20-1/2"

(516mm)

(230mm)

14"

(356mm)

16-1/2"

(419mm)

30-3/4"

(780mm)

13-1/2"

(340mm)

12"

(300mm)

(102mm)

(226mm)

1/2"

(11mm)

30-1/4"

(768mm)

20-1/2"

(516mm)

18-1/2"

(470mm)

12"

(304.8mm)

13-3/4"

(347mm)

9-1/2"

(238mm)

14"

(356mm)

(150mm)

(226mm)

(27mm)

15"

(381mm)

29-1/4"

(742mm)

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CADET 1.1 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS - Model 2462.100 Cadet Elongated 15" - Model 2467.100 Cadet Elongated 16-1/2" High Bowl YORKVILLE 1.1 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS - Model 2876.100 Yorkville Elongated 15" - Model 2878.100 Yorkville Elongated 16-1/2" High Bowl Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.
PAGE 2
con’t. FOR YORKVILLE TOILETS: con’t. FOR CADET TOILETS: INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around base flange. 4-1 WAX RING SEALANT 4-2 INSTALL NEOPRENE OR GRAPHITE FELT SEAL* Install seal evenly around waste flange (horn). Apply a thin bead of sealant around base flange. * Note: Wax seal not recommended for this application.
PAGE 3
7 SPONGE WASHER TANK MTG. BOLTS a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washers and nuts. b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface. INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
PAGE 4
11 CARE AND CLEANING When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish. TROUBLESHOOTING GUIDE NOTE: The presence of a small amount of water in the bottom of the tank is normal.