Installation Guide

ManualsBrandsAmerican Standard ManualsKitchenPortsmouth Single-Handle Pull-Out Sprayer Kitchen Faucet in Oil Rubbed Bronze

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

PUTTY

SINK OR

MOUNTING

SURFACE

SPOUT BASE

Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside

of sink or mounting surface. Hand tighten LOCKNUT (6).

Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening

the screws slightly each time until all are snug to ensure even pressure.

(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).

Insert SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and

mounting surface. Follow mounting instructions below to secure faucet to mounting surface.

(B) Installation less ESCUTCHEON (1).Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and

mounting surface. Do not use putty.

Plumbers' Putty or CaulkingAdjustable WrenchPhillips Screwdriver

RECOMMENDED TOOLS

Regular Screwdriver

Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).

Turn off water at

main supply.

CAUTION

Make certain the SEAL (9) is properly seated in recess of spout base.

M965456 Rev. 1.2

SINGLE CONTROL

KITCHEN PULL-OUT FAUCET

Installation

Instructions

Certiﬁed to comply with ANSI A112.18.1M

4285.100

4285.100F15

PORTSMOUTH

™

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Summary of content (5 pages)

PAGE 1
Installation Instructions PORTSMOUTH™ 4285.100 4285.100F15 SINGLE CONTROL KITCHEN PULL-OUT FAUCET Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M 9 6 5 4 5 6 R ev. 1.
PAGE 2
MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten. 2 1 Faucet supplies are 24" long from faucet base.
PAGE 3
5 TEST INSTALLED FAUCET Move HANDLE (1) down into "off" position. With HANDLE (1) down in "off" position, pull HAND SPRAY (2) from SPOUT (3). SPRAY (HOSE (4) should pull approximately 2 feet and direct open SPRAY END (5) into sink. Operate handle up and down, in COLD and HOT positions, to flush water lines thoroughly. Check HAND SPRAY (2) operation: SPRAY OPERATION With FAUCET on, press TOGGLE BUTTON (6) on SPRAY (3) to switch from stream to spray.
PAGE 4
7 SERVICE If Faucet Drips Proceed As Follows: Turn VALVE in OFF position. If faucet drips, operate HANDLE several times from OFF to ON position. Do not apply excessive force. FLOW CONTROL DEVICE may accumulate dirt. To remove the FLOW CONTROL DEVICE, unthread SPRAY AND HOSE ASSEMBLY and rinse clean FLOW CONTROL DEVICE. Clogged CARTRIDGE outlets or inlets may cause reduced flow. To clean, first turn off water supply then: Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
PAGE 5
PORTSMOUTH™ SINGLE CONTROL KITCHEN PULL-OUT FAUCET MODEL NUMBERS 4285.100 4285.100F15 M962994-0070A BUTTON AND SCREW KIT M964398-YYY0A HANDLE KIT M907302-YYY0A ESCUTCHEON CAP M953666-YYY220A (2.2 GPM) SPRAY WITH HOSE M953666-YYY150A (1.