Installation & Assembly

SINGLE CONTROL

PULL-DOWN BAR FAUCET

4433.410

4433.410F15

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Installation

Instructions

Certiﬁed t o comply with ANSI A112.18.1M

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

PUTTY

SPOUT BASE

SINK OR

MOUNTING

SURFACE

SPOUT BASE

Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside

of sink or mounting surface. Hand tighten LOCKNUT (6).

Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening

the screws slightly each time until all are snug to ensure even pressure.

Plumbers' Putty or Caulking

Adjustable Wrench

Phillips Screwdriver

RECOMMENDED TOOLS

Regular Screwdriver

Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).

Turn off water at

main supply.

CAUTION

QUINCE™

M 9 6 5 2 4 3 R E V. 1. 4

(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).

Make certain the SEAL (9) is properly seated in recess of faucet body. Insert SUPPLY HOSES (2), SPRAY HOSE (7)

and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions

below to secure faucet to mounting surface.

(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9)

is properly seated in recess of faucet body.Insert supply HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting

hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.

PAGE 1
Installation Instructions 4433.410 4433.410F15 QUINCE™ SINGLE CONTROL PULL-DOWN BAR FAUCET Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified t o comply with ANSI A112.18.1M M 9 6 5 2 4 3 R E V. 1.
PAGE 2
MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten. 2 1 Faucet supplies are 21" long from faucet base.
PAGE 3
5 CHECK CONNECTIONS FOR LEAKS. Move HANDLE into "off" position. Turn on water supplies and check connections for leaks. Operate HANDLE up and down, left and right to flush water lines thoroughly. Operate HAND SPRAY and check connections for leaks. CHECK CONNECTIONS FOR LEAKS 6 SERVICE If faucet drips, operate HANDLE several times from "off" to "on." Do not apply excessive force. Clogged CARTRIDGE outlets or inlets may cause reduced flow.
PAGE 4
QUINCE™ SINGLE CONTROL PULL-DOWN BAR FAUCET MODEL NUMBER 4433.410 4433.410F15 M922367-0070A SPRAY HOSE M964178-YYY220A (2.2 GPM) SPRAY ASSEMBLY M964178-YYY150A (1.