Installation Instructions

ManualsBrandsAmerican Standard ManualsKitchenBeale MeasureFill Single-Handle Pull-Down Sprayer Kitchen Faucet in Chrome

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965857 (4/18)

(A) Installation on 1-hole mounting surface:

• Make certain the SEAL (2) is properly seated in bottom recess of MOUNTING RING (10) and in top recess of MOUNTING

RING (10). Place mounting ring over mounting hole at the deck. Insert CABLES (12), HOSES (3) and SHANK (4) through

mounting ring and deck, seat SPOUT BASE onto sink or mounting surface. Do not use putty.

• From below: Insert CABLES (12) and HOSES (3) through PLASTIC WASHER (6), BRASS WASHER (7), and threaded

LOCKNUT (8).

• Assemble PLASTIC WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8) onto SHANK (5) from underside

of sink or mounting surface. Hand tighten LOCKNUT (8).

• Make sure faucet is aligned properly with handle on the right and logo facing directly forward.

• Use a screwdriver to tighten SCREWS (9) on LOCKNUT (8). Work your way around LOCKNUT (8), tightening the screws

slightly each time until all are snug to ensure even pressure.

(B) Optional: Installation on 3-hole mounting surface: Requires Deck Escutcheon - order separately

• Make certain the FOAM SEAL (14) is properly seated in bottom recess of DECK ESCUTCHEON (1). Do not use putty.

• Place deck escutcheon over mounting holes of the deck.

• Insert SUPPLY CABLES (12), HOSES (3), SPRAY HOSE (4) and SHANK (5) through hole of DECK ESCUTCHEON (1) and

mounting surface.

• Follow mounting instructions above to secure faucet to mounting surface.

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

BEALE

MeasureFill

™

KITCHEN FAUCET

INSTALLATION

INSTRUCTIONS

4931360

Flat Blade Screwdriver Adjustable WrenchPhillips Screwdriver

Certied to comply with ANSI A112.18.1M

B (OPTIONAL)

SPOUT BASE

SINK OR

MOUNTING

SURFACE

SPOUT BASE

CAUTION

Turn off water at

main supply

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 4931360 BEALE® MeasureFill™ KITCHEN FAUCET Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.
PAGE 2
INSTALL CONTROL BOX • Determine desired height and location (optional) and mark the top center line. Use a level to help mark the vertical center line for the two mounting locations. The distance between the two mounting holes is 2-3/8" (60 mm). Note: This dimension is important and must be maintained. If BOX is secured to a stud or cross brace with in the wall, drill small pilot holes for SCREWS (2).
PAGE 3
4 CONNECT CONTROL BOX • Connected with the battery box. The IR BUTTON LIGHT (2) will turn on, and the IP sensor is adjusting the sensitivity automatically. Several seconds later, it will then turn off. 5 MEASURED FILL FUNCTIONALITY • Turning the scale to the required amount and touching the INDUCTION WINDOW (1) will dispense quantitative water. Light is normally on during quantitative process and will shut off once the quantitative amount has been dispensed.
PAGE 4
6 SPRAY OPERATION • With FAUCET on, press TOGGLE BUTTON (1) on SPRAY (2) to switch from stream to spray. • Turn ON water at main supply. 3 • With handle in “off” position, unthread SPRAY (2) from HOSE (3). • Operate handle back to front, in COLD and HOT positions, to flush water lines thoroughly. • Replace SPRAY (2) onto HOSE (3). STREAM (AERATOR) • Please make sure that there is no cross threading.
PAGE 5
BEALE® MeasureFill™ KITCHEN FAUCET MODEL NUMBER 4931360 M918511-0070A CARTRIDGE SCREWS M970380-YYY0A SPRAY ASSEMBLY 4931888-YYY ESCUTCHEON AND SEAL (OPTIONAL) M951483-0070A CARTRIDGE M907315-YYY0A ESCUTCHEON CAP M970381-0070A AERATOR KIT M911705-0070A SEAL M970379-YYY0A MOUNTING RING M970378-YYY0A HANDLE KIT M962672-0070A MOUNTING KIT M970391-YYY0A PLUG BUTTON & SCREWS M970382-0070A FIXATION RING M970383-0070A WEIGHT M970385-0070A CONTROL BOX Replace the “YYY” with appropriate finish code POLI