Installation Sheet

ManualsBrandsAmerican Standard ManualsCommercial ProductsAmerican Standard Manual FloWise Urinal Flush Valve 3/4" Top Spud, 0.5 gpf

Installation Instructions

Ultima

™

Manual

Urinal Flush Valve, Piston-Type

3/4" Top Spud, 0.5 gpf

M965360 REV. 1.9 (5/19)

MODEL NUMBERS

7015.051

6045.051

Certified to comply with:

• ASSE 1037

• ADA Compliant

OPERATING PRESSURE:

• 25 psi (flowing) - 80 psi (static)

FLOW REQUIREMENT:

• 10gpm (37.9 L/min).

OPERATING PR

• 25

(

flowin

FLOW RE

UIR

• 10

m (37.9 L/

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@lixilamericas.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

Summary of content (6 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s Ultima™ Manual MODEL NUMBERS Urinal Flush Valve, Piston-Type 3/4" Top Spud, 0.5 gpf 6045.051 7015.051 OPERATING PRESSURE: PRE • 25 psi (flowing) - 80 psi (static) FLOW REQUIRE REQUIREMENT: • 10gpm (37.9 L/min). L/m Certified to comply with: • ASSE 1037 • ADA Compliant © 2019 AS America, Inc. M965360 REV. 1.9 (5/19) NOTE TO INSTALLER: Please give this manual to the customer after installation.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Fig. 1 Roughing-in Dimensions GENERAL DESCRIPTION: FINISHED WALL MANUAL FLUSH VALVE, 0.5 GPF 38mm-127mm (1-1/2-5") 108mm-133mm (4-1/4" to 5-1/4") Exposed Flushometer for 3/4" Top Spud Fixtures Exclusive, self cleaning piston-operated flush valve. SUPPLY DN 19mm (3/4" I.P.S.
PAGE 4
1 INSTALL SWEAT SOLDER Fig.3 Fig.3a ADAPTER; Fig. 3 CAUTION FINISHED WALL Turn water supplies off before beginning CENTER LINE OF FIXTURE SPUD A Note: Install Optional Sweat Solder Adapter (Supplied) for copper pipe supply line. Fig. 3. (A-B)= C 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. B 32mm (1-1/4) FILE EDGES 2. Cut the supply pipe 1-1/4" (A-B=C) shorter then the measurement taken in Step 1.
PAGE 5
4 INSTALL FLUSH VALVE; Fig. 6a Fig. 6a & 6b 3 1. As shown in Fig. 6a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 6a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 6b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6).
PAGE 6
ADJUST SUPPLY STOP; Fig. 8 Fig. 8 REMOVE COVER IMPORTANT: To avoid overflowing, the SUPPLY STOP (3) must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. The fixture and drain must be able to handle a continuous flow in case of a flush valve failure. Valve is designed to provide stated flush volume with a 10 GPM flow rate. 3 2 COUNTER-CLOCKWISE OPENS CONTROL STOP 1. Remove COVER (2) from SUPPLY STOP (3).