Installation Instructions

ManualsBrandsAmerican Standard ManualsBathManual 0.5 GPF Urinal Flush Valve with Side Mount Operator in Chrome

M965832 (6/17)

FLUSH VALVE

Exposed Urinal Flushometer

with Side-Mount Operator

for 3/4" Top Spud Urinals

OPERATING PRESSURE:

• 20 psi (owing) - 80 psi (static)

FLOW REQUIREMENT:

• 10gpm (37.9 L/min).

** Water pressure over 80 psi is not

recommended with most plumbing xtures

Certied to comply with:

• ASSE 1037

• ANSI/ASME A112.19.2

• ADA Compliant

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

MODEL NUMBERS

6045SM013

6045SM051

6045SM101

Summary of content (7 pages)

PAGE 1
FLUSH VALVE MODEL NUMBERS Installation Instructions Exposed Urinal Flushometer with Side-Mount Operator for 3/4" Top Spud Urinals 6045SM013 6045SM051 6045SM101 OPERATING PRESSURE: • 20 psi (flowing) - 80 psi (static) FLOW REQUIREMENT: • 10gpm (37.9 L/min). ** Water pressure over 80 psi is not recommended with most plumbing fixtures Certified to comply with: • ASSE 1037 • ANSI/ASME A112.19.2 • ADA Compliant NOTE TO INSTALLER: Please give this manual to the customer after installation.
PAGE 2
Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping UNPACKING 1. R emove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions 147 mm (5-13/16") GENERAL DESCRIPTION FINISHED WALL Fig.1 108 mm-133 mm (4-1/4" to 5-1/4") MANUAL FLUSH VALVE, 0.5 GPF Exposed Flushometer for 3/4" Top Spud Fixtures 38 mm-127 mm (1-1/2-5") SUPPLY DN 19 mm (3/4" I.P.S. For 3/4" Top Spud) • 20 psi (flowing) - 80 psi (static) FLOW REQUIREMENT: • 10gpm (37.9 L/min).
PAGE 4
FLUSH VALVE INSTALLATION Fig. 3 FINISHED WALL 1 INSTALL SWEAT ADAPTER; Fig. 3 CAUTION CENTER LINE OF FIXTURE SPUD A Turn water supplies off before beginning (A-B)= C Note: Install Optional Sweat Adapter (Supplied) for copper pipe supply line. B 32mm (1-1/4") FILE EDGES 1. M easure the distance (A) from the finished wall to the center of the inlet spud on the fixture. 2. Cut the supply pipe 1-1/4" (A-B=C) shorter than the measurement taken in Step 1.
PAGE 5
4 INSTALL FLUSH VALVE; Fig. 6a & 6b Fig. 6a 3 1. As shown in Fig. 6a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 6a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 6b) directly above the VERTICAL TUBE (7) and VACUUM BREAKER COUPLING NUT (6).
PAGE 6
ACTIVATION; Fig. 8 Fig. 8 5 Note: Four (4) “C” Cell batteries are not factory installed inside the Flush unit. 1. Load 4 “C” Alkaline BATTERIES (5) onto BATTERY TRAY (1). 2. Install battery tray into SIDE MOUNT OPERATOR (2) and tighten SCREW (3) using WRENCH (4) provided. (Note: last three turns of the wrench will activate the automatic flushing unit) 3 4 + + + 2 5 1. Remove BATTERY TRAY (1) by loosening SCREW (3). Fig. 9 2. Remove FRONT COVER (2) and remove SENSOR ADJUSTMENT TOOL (4). Fig.
PAGE 7
11 ADJUST SUPPLY STOP; Fig. 13 Fig. 13 REMOVE COVER IMPORTANT: To avoid overflowing, the SUPPLY STOP (3) must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. Valve is designed to provide stated flush volume with a 25 GPM flow rate. 3 2 COUNTER-CLOCKWISE OPENS CONTROL STOP 1. R emove COVER (2) from SUPPLY STOP (3).Turn on water supply 1/4 turn to 1/2 turn(CCW) and test for leaks. Note: Unit may flush for approximately 5 to 10 sec.