Installation Guide

ManualsBrandsAmerican Standard ManualsBathSelectronic DC-Powered 0.5 GPM Touchless Lavatory Faucet with Cast Spout in Polished Chrome

Cast Spout and

Gooseneck Spout

M965650 Rev. 2.3 (9/20)

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any

components will void the warranty.

Installation Instructions

Certied to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@lixilamericas.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

SELECTRONIC

Proximity Faucets

605X.102

605X.163

605X.104

605X.164

605X.105

605X.165

MODEL NUMBERS

2-3

4-6

7-8

9-10

Product No.'s & Options

Speciﬁcations

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Parts

2-3

4-6

7-8

9-10

Summary of content (11 pages)

PAGE 1
Installation Instructions SELECTRONIC® Proximity Faucets MODEL NUMBERS 605X.102 605X.104 605X.105 605X.163 605X.164 605X.165 Cast Spout and Gooseneck Spout CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. UNPACKING The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
PAGE 3
Fig. 1 GENERAL DESCRIPTION: Roughing-in Dimensions Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in check valves, and flexible stainless steel 16-1/4" reach inlet hose for spout connection.
PAGE 4
2 MOUNT CONTROL BOX; Fig. 2 Fig. 2 LAVATORY RIM OR MOUNTING SURFACE 1. Determine location of CONTROL BOX (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made. 14" (356mm) NOTE: CONTROL BOX SUPPLY HOSE is 20". Distance between wall supply and CONTROL BOX (1) must be taken into consideration. SUPPLIES ENCLOSURE MOUNTING HOLES 1 2-3/4" (71mm) 2.
PAGE 5
Fig. 1 ELECTRICAL INSTALLATION Product 1 Page Plug-in AC Power Kit (PK00.PAC) 5 Hard-Wired AC Power Kit (PK00.HAC) 5 MULTI-AC Power Kit (PK00.MAC) 6 Fig. 1a 2 Fig. 1b 3 5a A DC VERSIONS (PWRX & 5 STANDARD BATTERY); Fig. 1 1. Remove CONTROL BOX COVER (1). Fig. 1. INSTALL BATTERY 2. Feed the CABLES (2) through the top of CONTROL BOX (3). Fig. 1a. 4 -P2 CR FOR STANDARD BATTERY VERSION ONLY 3.
PAGE 6
B AC VERSIONS (HARDWIRE / PLUG-IN); Fig. 2 Fig. 2 CAUTION 2 Disconnect AC power supply before opening CONTROL BOX. 3 1 NOTE: For AC installation, make power supply connection before mounting CONTROL BOX (3) to wall. 1. Remove CONTROL BOX COVER (1). Feed the CABLES (2) from the Faucet through the top of ENCLOSURE (3). Install CONNECTOR LOCKING DEVICE (16).Fig. 2. FOR PLUG-IN HOOKUP ONLY 2a. Insert POWER CORD (8) through POWER SUPPLY GROMMET (9) Fig. 2a. 3a.
PAGE 7
Fig. 3 Unit #2 Unit #1 Unit #3 Already installed 10 ft. EXTENSION CABLE AC POWER SUPPLY OR *MAXIMUM OF 15 UNITS PER AC POWER SUPPLY. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. BLACK & WHITE POWER CONNECTIONS C MULTI-AC VERSION (DAISY-CHAIN); Fig. 3, 3a Important: All control box covers must be removed before beginning to make daisy-chain connections. Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections.
PAGE 8
Fig 1 TEST INSTALLED FAUCET TION DETEC N ZO E TO ENSURE A LAMINAR WATER FLOW, the air must be slowly purged from the spout. To do so, cover the SENSOR (1) while slowly opening the water supply valves. When the water flows as a solid, smooth, steady stream, uncover the SENSOR (1) and fully open the water supply valve. Fig. 1. MAINTENANCE A HAND WASH SENSOR OPERATION; Fig. 1 When the Sensor detects a user, the water immediately starts to flow.
PAGE 9
D INSTALL / REPLACE THE BATTERY or Fig. 4 PWRX; Fig. 4 CR-P2 2 1. Remove COVER from CONTROL BOX (1). 1 2. Disconnect BATTERY HOLDER (3) from CABLE (5). STANDARD BATTERY 5 6 3. Remove old BATTERY from BATTERY HOLDER (3). Install new BATTERY (2) making sure the terminal side is inserted first and shape of the battery follows the shape of the BATTERY HOLDER (3). 3 4. To replace PWRX BATTERY PACK (4), unplug and replace with new Power Pack. 5. Reconnect BATTERY HOLDER (3) to CABLE (5). 6.
PAGE 10
Fig.6 F CONVERT RIGID GOOSENECK SPOUT TO SWING SPOUT; Fig. 6 2 The GOOSENECK SPOUT is shipped from the factory as a rigid assembly. To convert the GOOSENECK SPOUT into a SWING SPOUT, proceed as follows: 1 1. Remove SET SCREW (1) from back of GOOSENECK SPOUT (2) with a flat blade screwdriver. Fig. 6. 3 2. Install SWIVEL SET SCREW (3) on the back of GOOSENECK SPOUT (2). SWIVEL SET SCREW (3) is found in hardware bag inside the product box. (USE SHORT SET SCREW FOR SWIVEL SPOUT) Fig.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. NO OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES IS INTERNAL SUPPLY STOP OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO 1 RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 2 NO NO 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR.