Installation Guide

ManualsBrandsAmerican Standard ManualsBathSelectronic DC Powered 0.5 GPM Touchless Lavatory Faucet with 6 in. Gooseneck Spout in Polished Chrome

Installation Instructions

(In Toronto Area only: 1-905-3061093)

SELECTRONIC™

Proximity Faucets

Certiﬁed to comply with ASME A112.18.1M

To l e a r n more a b o u t A m e r ican Sta n d a rd Fa u c e t s v i s i t o u r website a t : www.us.amstd.com or U.S.

customer's e-mail us at: sensor@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call

(855) 752-9259 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-3061093)

Product No.'s & Options

Speciﬁcations

How to Install

Electrical Hook-up

Maintenance

FAQ,s

Replacement Parts

Cast Spout and

Goose Neck Spout

2-3

4-6

7-8

M968809 Rev.1.6

6055.102

6055.105

6056.102

6056.105

6055.104 6056.104

6057.102

6057.105

6055.163

6055.165

6056.163

6056.165

6055.164 6056.164

6057.163

6057.165

6" GN Spout

Cast Spout

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any

components will void the warranty.

Summary of content (11 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s SELECTRONIC™ Proximity Faucets Cast Spout 6055.104 6056.104 6057.105 6055.105 6056.105 6057.102 6055.102 6056.102 6" GN Spout 6055.164 6056.164 6057.165 6055.165 6056.165 6057.163 6055.163 6056.163 Cast Spout and Goose Neck Spout CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Certified to comply with ASME A112.18.1M Product No.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. UNPACKING 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton.
PAGE 3
Fig. 1 Roughing-in Dimensions 11-1/8" (284mm) 6-1/8" (155mm) 131mm (5-1/8) 141mm (5-1/2) 49mm (2) 81mm (3-3/16) 32mm (1-1/4) 49mm (2) 125mm (4-7/8) CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. 114mm (4-1/2) 381mm (15) 381mm (15) GENERAL DESCRIPTION: 500mm (20") 1524mm (60) 3/8" COMP. Electronic faucet with proximity operation.
PAGE 4
2 MOUNT ENCLOSURE; Fig. 2 Fig. 2 1. Determine location of ENCLOSURE (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made. NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance between wall supply and ENCLOSURE (1) must be taken into consideration. LAVATORY RIM OR MOUNTING SURFACE 14" (356mm) SUPPLIES ENCLOSURE MOUNTING HOLES 1 2-3/4" (71mm) 2. Remove 4 screws from COVER (2) and pull off COVER (2).
PAGE 5
ELECTRICAL INSTALLATION Fig. 1 1 1 DC VERSION (BATTERY); Fig. 1 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Feed the EXTENSION CABLES (2) from the Faucet through the top of ENCLOSURE (3). Fig. 1a. 3. Install BATTERY (4) if not already installed, make sure the shape of the BATTERY (4) follows the shape of the BATTERY HOLDER (5). Fig. 1b. Fig. 1a 4. Insert the BATTERY CONNECTOR (5a) through GROMMET (6) as shown. Fig. 1c. Fig. 1b 2 3 5.
PAGE 6
2 AC VERSION; Fig. 2 CAUTION Fig. 2 1 Before opening ENCLOSURE disconnect AC power supply. NOTE: For AC installation see Fig. 2b. Make power supply connection before mounting ENCLOSURE (1) to wall. 1. Remove ENCLOSURE COVER (1). Fig. 2. 2. Feed the EXTENSION CABLES (2) from the Faucet through the top of ENCLOSURE (3). Fig. 2a. Fig. 2b Fig. 2a 3. Remove SPLIT PLUG (4) from POWER SUPPLY GROMMET (5). Insert POWER CORD (7) into SPLIT PLUG (4).
PAGE 7
Fig. 3 Unit #1 Unit #2 Unit #3 FAUCET WIRE CONNECTORS FAUCET WIRE CONNECTORS FAUCET WIRE CONNECTORS 10 ft. EXTENSION CABLE 6 10 ft. EXTENSION CABLE 6 9 6 9 5 5 8 8 AC POWER SUPPLY 3 FOR AC-VERSION Fig. 3a (MULTI HOOK-UP); Fig. 3, 3a, 3b NOTE: For AC installation see “AC VERSION; Fig. 2b.” Make power supply connection before mounting ENCLOSURE (1) to wall. Unit #1 2 SENSOR CABLES 1a 1. Remove COVERS from all ENCLOSURES (2). Fig. 3. 6 1 2.
PAGE 8
MAINTENANCE Fig 1 TION DETEC ZONE 1 HAND WASH SENSOR OPERATION; Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop Two seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on to off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone.
PAGE 9
4 HOW TO CLEAN FILTER; Fig. 4 CAUTION Fig.4 Before opening ENCLOSURE disconnect AC power supply. 1. Remove ENCLOSURE COVER. 7/16" SOCKET 2. Close SUPPLY STOP (1) with 4mm Hex wrench. Note: Keep water flowing out of faucet while shutting off. 3. Unthread STRAINER (2) using a 7/16" socket. 2 1 4. Pull out the STRAINER (2) and clean with an old toothbrush. Rinse thoroughly with water. 5. Install the STRAINER (2) back in its place and tighten with a 7/16" socket. Caution: do not over tighten strainer.
PAGE 10
7 GENERAL CLEANING; Fig. 7 Fig.7 1. For general cleaning use a damp, soft cloth to clean the spout and the sensor. 2. For cleaning dirt use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using anything that may scratch the spout surface. Never use polishing power, detergent or a nylon scrub brush. They will damage the surface of the spout or Sensor.
PAGE 11
M 9 6 8 8 0 9 R ev. 1.