Installation Sheet

ManualsBrandsAmerican Standard ManualsCommercial ProductsAmerican Standard Selectronic Dual Flush 1.28/1.1 GPF Toilet Flushometer Valve

Installation Instructions

(In Toronto Area only: 1-905-3061093)

Certiﬁed to comply with ASME A112.19.2M

NOTE TO INSTALLER: Please give this manual to the customer after installation.

SELECTRONIC™

PROXIMITY DUAL FLUSH TOILET FLUSH VALVE

1.6 / 1.1 GPF, 1.28/1.1 GPF

Exposed Flushometer for 1-1/2" Top Spud Bowls

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

ONE SENSOR FITS ALL

• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and ush valves.

• Range can be adjusted manually or with optional remote control.

• Sensor Features Low Battery Indicator.

M965051 REV.1.5

6065.561

6065.761

6065.721

6065.521

MODEL NUMBERS

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

ONE SENSOR FITS ALL

• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and ush valves.

• Range can be adjusted manually or with optional remote control.

• Sensor Features Low Battery Indicator.

To lear n more about Amer i c a n S tandard Fa u c e t s v i s i t o u r website a t : www.americanstandard-us.com

or U.S. customer's e-mail us at: faucetsupport@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-3061093)

This flushometer valve is intended to be used with

listed/certified 1.6gpf / 1.1gpf dual flush bowls only.

Summary of content (10 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s SELECTRONIC™ PROXIMITY DUAL FLUSH TOILET FLUSH VALVE 1.6 / 1.1 GPF, 1.28/1.1 GPF MODEL NUMBERS 6065.561 6065.761 6065.721 6065.521 Exposed Flushometer for 1-1/2" Top Spud Bowls This flushometer valve is intended to be used with listed/certified 1.6gpf / 1.1gpf dual flush bowls only. CLOG RESISTANT • Self-cleaning piston valve prevents clogging and reduces maintenance.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. 1. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Fig. 1 GENERAL DESCRIPTION: Roughing-in Dimensions SELECTRONIC™ PROXIMITY TOILET FLUSH VALVE DETECTION ZONE 400mm-800mm (15-3/4 TO 31-1/2) 72mm (2-7/8) FINISHED WALL 57mm (2-1/4 MIN.) 15˚ 116mm (4-5/8) MANUAL OVERRIDE BUTTON SUPPLY DN 25mm (1” I.P.S.) *CRITICAL LEVEL -C-L- 115mm-134mm (4-1/2 TO 5-1/4) 293mm (11-1/2) *-C-L165mm (6-1/2) Exposed Flushometer for 1-1/2" Top Spud Fixtures Exclusive, self cleaning piston-type flush valve with proximity operation and manual override.
PAGE 4
1 INSTALL THE SWEAT SOLDER ADAPTER; Fig. 3 CAUTION Fig.3 FINISHED WALL Turn water supplies off before beginning A Note: Install Optional Sweat Solder Adapter (Supplied) for copper pipe supply line. Fig. 3. (A-B)= C 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. B CENTER LINE OF FIXTURE SPUD 32mm (1-1/4) FILE EDGES 2. Cut the supply pipe 1-1/4" (A-B=C) shorter then the measurement taken in Step 1.
PAGE 5
4 FLUSH OUT SUPPLY LINES; Fig. 6 Fig. 6 2 1. Remove COVER (1) from SUPPLY STOP (2). REMOVE COVER 2. With a flat blade screwdriver open SUPPLY STOP (2). 1 3. Turn on water supply to flush line of any debris or sediment. 2 4. Close SUPPLY STOP (2) and replace COVER (1). COUNTER-CLOCKWISE OPENS CONTROL STOP CLOCKWISE CLOSES CONTROL STOP 453 LEFT OR RIGHT HAND INSTALLATION; Fig. 7 Fig. 7 2 The UNIT is shipped with the inlet flange on the right side.
PAGE 6
INSTALL FLUSH VALVE; Fig. 8a & 8b Fig. 8a 3 1. As shown in Fig. 8a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 8a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 8b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6). Make sure that GASKET (10) is installed.
PAGE 7
8 HOW TO RETROFIT OUR VALVE; Fig. 10 Fig. 10 6 Fig. 10a 2 1 (Replaces Industry Standard Manual and Electronic Valves) Fig. 10b CLEAN CONNECTIONS 4 5 Note: In most Retrofits the wall escutcheon, supply stop, cover tube and vacuum breaker do not have to be replaced. If these items do need replacement they must be purchased separately or order the complete flush valve assembly from American Standard. 3 1. Remove COVER (1) from SUPPLY STOP (2) if installed. Fig. 10. 2. Turn water supply off. Fig.
PAGE 8
11 HOW TO SET DETECTION RANGE 10 (If Required); (purchased after May 2013) Fig. 13 Fig. 13 & 14 Note: The detection distance is preset and is ideal for most installations. Should an adjustment be required follow the steps below. 6 Fig. 13b Fig. 13a 3 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of top half of FLUSH VALVE (3). Fig. 13a. 1 VIEW “A” 2. Rotate CAP (3) to the right and pull off. Fig. 13b. 3. Turn CAP (3) over and disconnect SENSOR CABLE (4) from BATTERY HOLDER (5). Fig.
PAGE 9
10a HOW TO SET DETECTION RANGE (If Required) ; (purchased before June 2013) Fig. 15 Fig. 15 & 16 Note: The detection distance is preset and is ideal for most installations. Should an adjustment be required follow the steps below. Fig. 15b Fig. 15a 6 3 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of top half of FLUSH VALVE (3). Fig. 15a. 1 2. Rotate CAP (3) to the right and pull off. Fig. 15b. VIEW “A” 3. Turn CAP (3) over and disconnect GREY SENSOR WIRE (4) from BATTERY COVER (5).
PAGE 10
9 M965051 REV.1.5 NO NO NO YES NO 1. CLOSE STOP VALVE, 2. REPLACE SOLENOID KIT. 3. RE-ASSEMBLE AND INSTALL UNIT. 4. OPEN STOP VALVE. YES TEST SENSOR. DISCONNECT GRAY FLAT WIRE FROM BATTERY COVER AND RE-CONNECT. SENSOR SHOULD FLASH FOR 5 SECONDS. DOES IT FLASH? NO LOOK FOR REPEATED DOUBLE FLASH ON SENSOR NO YES REPLACE SENSOR SEE STEP 10, page 6 in manual INSTALL NEW BATTERY RETRY AUTO FLUSH YES 1. COVER SENSOR FOR 10 SECONDS 2. UNCOVER SENSOR FOR 10 SECONDS.