Installation Instructions

ManualsBrandsAmerican Standard ManualsBathUltima Selectronic AC Powered Toilet 1.1/1.6 GPF Dual Flush Valve in Chrome

Certied to comply with ASME A112.19.2

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

Ultima

™

Selectronic

Battery Powered

Toilet Flush Valve, Piston-Type

MODEL NUMBERS

606B.111 606B.121 606B.161 606B.721 606B.761

Exposed Flush Valve

for 1-1/2" Top Spud Bowls

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any components

will void the warranty.

COVER PLATE

(Required for Front Installation Only)

M965644 EN REV. 2.3 (10/19)

Product to be used with WaterSense Certied Fixture with

the same rated ush volume.

Summary of content (14 pages)

PAGE 1
Installation Inst ru ct io n s Ultima™ Selectronic® Battery Powered MODEL NUMBERS 606B.111 606B.121 606B.161 606B.721 606B.761 Toilet Flush Valve, Piston-Type COVER PLATE (Required for Front Installation Only) Exposed Flush Valve for 1-1/2" Top Spud Bowls Product to be used with WaterSense Certified Fixture with the same rated flush volume. CAUTION: Use only American Standard supplied transformers and cable sets.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions (Front Installation Shown) GENERAL DESCRIPTION: SELECTRONIC® PROXIMITY TOILET FLUSH VALVE for 1-1/2" Top Spud Fixtures Right or Left Hand Installation See (Section 5) for converting Flush Valve to Left Hand Installation. CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. 4" (102 mm) SQ. BOX DEVICE COVER (PLASTER RING).
PAGE 4
RECOMMENDED TOOLS; Fig. 2. Fig. 2 1. Teflon Tape 2. Flat Blade Screwdriver 3. Adjustable Wrench 4. Tape Measure 5. Hacksaw 6. Tubing Cutter 7. File 8. For Sweat Connection; Solder and Torch 9. 2.5 mm Hex Wrench 10. 1.5 mm Hex Wrench 2 1 3 4 10' 6 8 5 7 PRIOR TO INSTALLATION 9 10 • Flush all water lines prior to operation. Dirt and debris can cause flush valve to run continuously. Note: Prior to installing the Selectronic™Flush Valve the following items must be installed. 1. Toilet 2.
PAGE 5
FLUSH VALVE INSTALLATION Fig.3 FINISHED WALL 1 INSTALL SWEAT ADAPTER; Fig. 3 CAUTION A Turn water supplies off before beginning (A-B)= C Note: Install Optional Sweat Adapter (Supplied) for copper pipe supply line. 1. M easure the distance (A) from the finished wall to the center of the inlet spud on the fixture. B 32mm (1-1/4") FILE EDGES 2. Cut the supply pipe 1-1/4" (A-B=C) shorter than the measurement taken in Step 1. File any rough edges off the end of the supply pipe. CLEAN ADAPTER 3.
PAGE 6
F LUSH OUT SUPPLY LINES; Fig. 6 4 Fig. 6 2 1. R emove STOP VALVE COVER (1) from STOP VALVE (2). REMOVE COVER 2. Open STOP VALVE (2) with a flat blade screwdriver. 1 3. Turn on water supply to flush line of any debris or sediment. 2 4. Close STOP VALVE (2) and replace STOP VALVE COVER (1). 5 COUNTER-CLOCKWISE OPENS STOP VALVE LEFT OR RIGHT HAND INSTALLATION; Fig. 7 CLOCKWISE CLOSES STOP VALVE The unit is shipped with the adjustable tailpiece on the right side.
PAGE 7
ELECTRICAL INSTALLATION Fig. 9 10' EXTENSION 2 INSTALL POWER SUPPLY AND MAKE ELECTRICAL CONNECTIONS; Fig. 9 (remote and front installation) 7 CAUTION 7 Ensure that the line power to bathroom is OFF prior to making connections. BLACK & WHITE POWER CONNECTIONS 1. Connect Black and White power connections to AC TRANSFORMER (1). Mount AC TRANSFORMER (1) onto ELECTRICAL BOX (2). 1 NOTE: AC Transformer must be installed on the outside of the Electrical Box. 2.
PAGE 8
Fig.10b Unit #1 Unit #2 Already installed 3 2a Unit #3 2 1 BLACK & WHITE POWER CONNECTIONS (See electrical installation instructions, page 5) *MAXIMUM OF 15 UNITS PER TRANSFORMER. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. 8b MULTI-AC VERSION (DAISY-CHAIN); Fig. 10b. CAUTION Ensure that the line power to bathroom is OFF prior to making connections. Important: All cover plates must be removed before beginning to make daisy-chain connections.
PAGE 9
CONNECTIONS 9 COVER PLATE FRAME AND COVER PLATE INSTALLATION Fig. 11 Fig.10a SLOT SLOT (front installation); Fig. 11 1 1. After power supply is remotely installed and wire connections are completed, install the COVER PLATE FRAME (1) onto the ELECTRICAL BOX (2). 3 2 2. Install the two tabs on the back side of the COVER PLATE (3) into the two Slots located on the top edge of the COVER PLATE FRAME (1). Push on bottom until it snaps into place.
PAGE 10
B SET DETECTION RANGE Fig. 13 (if Required); Fig. 13 & 14 1 Note: The detection distance is preset and ideal for most installations. Should an adjustment be required, follow the steps below. 1. To remove the COVER PLATE (1), insert WIRE KEY (2) (supplied) into the two holes located at the bottom of the COVER PLATE (1). Push the WIRE KEY (2) up until it releases the bottom clips. Pull the bottom edge away and lift the COVER PLATE (1) off. Fig. 13. 2 2.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION IS ANGLE STOP OPEN? NO OPEN VALVE YES LOW VOLTAGE. TEST OUTPUT OF TRANSFORMER. MUST BE >5.4 VAC. YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT TRANSFORMER TO SENSOR. FLASH ON SENSOR FOR 5 SECONDS? 1 2 NO 1 NO 2 BAD TRANSFORMER. REPLACE. REPEAT. DAMAGED SENSOR. REPLACE SENSOR. YES PUSH MANUAL OVERRIDE BUTTON; WILL THE UNIT FLUSH? DAMAGED SOLENOID. REPLACE SOLENOID YES NO REPLACE PISTON ASSEMBLY.
PAGE 12
BEFORE November 2017 M964120-0020A ESCUTCHEON & CONDUIT ASSEMBLY Ultima™ Selectronic® Battery Powered M964943-0021100A COVER ASSEMBLY (1.1 gpf) M964943-0021280A COVER ASSEMBLY (1.28 gpf) M964943-0021600A COVER ASSEMBLY (1.6 gpf) Toilet Flush Valve, Piston-Type MODEL NUMBERS 606B.111 606B.121 606B.161 606B.721 606B.761 M964943-0023000A COVER ASSEMBLY (1.28/1.1 gpf) M918004-0070A WALL FLANGE SET SCREW M964943-0024000A COVER ASSEMBLY (1.6/1.
PAGE 13
AFTER November 2017 M964120-0020A ESCUTCHEON & CONDUIT ASSEMBLY Ultima™ Selectronic® Battery Powered M970345-0021100A COVER ASSEMBLY (1.1 gpf) M970345-0021280A COVER ASSEMBLY (1.28 gpf) M970345-0021600A COVER ASSEMBLY (1.6 gpf) Toilet Flush Valve, Piston-Type MODEL NUMBERS 606B.111 606B.121 606B.161 606B.721 606B.761 M970345-0023000A COVER ASSEMBLY (1.28/1.1 gpf) M918004-0070A WALL FLANGE SET SCREW M970345-0024000A COVER ASSEMBLY (1.6/1.
PAGE 14
AFTER November 2017 M964120-0020A ESCUTCHEON & CONDUIT ASSEMBLY Ultima™ Selectronic® Battery Powered M970345-0021100A COVER ASSEMBLY (1.1 gpf) M970345-0021280A COVER ASSEMBLY (1.28 gpf) M970345-0021600A COVER ASSEMBLY (1.6 gpf) Toilet Flush Valve, Piston-Type MODEL NUMBERS 606B.111 606B.121 606B.161 606B.721 606B.761 M970345-0023000A COVER ASSEMBLY (1.28/1.1 gpf) M918004-0070A WALL FLANGE SET SCREW M970345-0024000A COVER ASSEMBLY (1.6/1.