Dimensions Guide

BOTTOM MOUNT

KITCHEN FAUCETS

Installation

Instructions

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Certiﬁed to comply with ANSI A112.18.1M

M965719 (10/15)

Turn VALVES (1) to off position.

Insert ADAPTOR (7) with larger diameter over the VALVE STEM (4).

Align LEVER (2) or WRIST BLADE HANDLE (3) and install onto VALVE STEM (4).

Insert BLUE INDEX (5) into cold valve (right side) and red INDEX (6) into hot valve (left side).

Insert HANDLE SCREW (6) into HANDLES and tighten with screwdriver.

INSTALL HANDLES

Turn off water at

main supply.

CAUTION

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

6403 Series

6404 Series

Push TUBING (7) ends into VALVES (6, 6a) side outlets. Insert VALVES (6, 6a)

into mounting holes from underside of ledge.

Install LOCKNUTS (1, 1a), BRASS WASHERS (2) and RUBBER WASHERS

(3, 3a) onto valve and center shanks.

Place RUBBER RING (8) into ESCUTCHEON (9) and thread onto VALVES (6, 6a)

until snug against internal stop.

Tighten LOCKNUT (1, 1a) to secure VALVES (6, 6a) into position.

Firmly tighten COUPLING NUTS (5).

Install FERRULE (4) into COUPLING NUT (5). Thread onto VALVE (6, 6a) and

loosely tighten COUPLING NUTS (5).

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of

right VALVE using appropriate connector.

Place SPOUT RUBBER RING (10) into SPOUT BASE (11) and thread onto VALVE

SHANK (12) and tighten.

INSTALL VALVE ASSEMBLIES

HOT

COLD

MOUNTING

LEDGE

5/16" MIN.

MOUNTING SURFACE

PAGE 1
Installation Instructions 6403 Series 6404 Series BOTTOM MOUNT KITCHEN FAUCETS Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M965719 (10/15) Recommended tools Screwdriver 1 Channel Locks INSTALL VALVE ASSEMBLIES CAUTION Tubing Cutter Adjustable Wrench Turn off water at main supply.
PAGE 2
3 INSTALL SPOUT CAUTION Turn off water at main supply. Insert SPOUT (1) into SPOUT BASE (2) and tighten BONNET NUT (3) onto SPOUT BASE (2). 70˚ C/L 70˚ 3 1 6404 Series (Limited Swivel Spout) MOUNTING LEDGE 2 HOT 3 COLD 4 TO CHANGE SPOUT FROM RIDGID TO FULL SWIVEL SPOUT: (6403 SERIES) 2 1 Unscrew SPOUT NUT (1) and remove SPOUT (2). Take SPOUT CLIP (3) off SPOUT (2) and remove RUBBER RING (4). Replace RUBBER RING (4) with seperate PLASTIC RING (5) packed with faucet.
PAGE 3
6 INSTALL SIDE SPRAY Feed SPRAY HOSE (1) through SPRAY HOLDER (2) and attach COUPLING NUT (3) of HOSE (1) to HOSE ADAPTOR (4) on valve body. Tighten COUPLING NUT (3) firmly. 1 2 4 3 7 TEST INSTALLED FAUCET Remove AERATOR. With handle in OFF position, turn on water supplies and check all connections for leaks. 8 Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. Turn handles into OFF position and replace AERATOR.