Installation Guide

ManualsBrandsAmerican Standard ManualsCommercial ProductsAmerican Standard Washbrook FloWise 0.125 GPF Ultra High Efficiency Pint Urinal System with Selectronic Urinal Flush Valve and Urinal Fixture

Installation Instructions

(In Toronto Area only: 1-905-3061093)

Certiﬁed to comply with ASME A112.19.2M

NOTE TO INSTALLER: Please give this manual to the customer after installation.

SELECTRONIC™

PROXIMITY URINAL FLUSH VALVE

0.125 GPF & (0.5 LPF)

Exposed Flushometer

for 3/4" Top Spud Urinals

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

ONE SENSOR FITS ALL

• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and ush valves.

• Range can be adjusted manually or with optional remote control.

• Sensor Features Low Battery Indicator.

M968541 REV.1.2

6063.013

6590.525

MODEL NUMBERS

To learn more about American Standard Faucets visit our website at: www.americanstandard-us.com

or U.S. customer's e-mail us at: faucetsupport@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-3061093)

Installation Instructions

Summary of content (10 pages)

PAGE 1
Installation Instructions SELECTRONIC™ PROXIMITY URINAL FLUSH VALVE 0.125 GPF & (0.5 LPF) MODEL NUMBERS 6063.013 6590.525 Exposed Flushometer for 3/4" Top Spud Urinals CLOG RESISTANT • Self-cleaning piston valve prevents clogging and reduces maintenance. ONE SENSOR FITS ALL • Only 1 sensor for entire Selectronic™ line of faucets, urinals, and flush valves. • Range can be adjusted manually or with optional remote control. • Sensor Features Low Battery Indicator. Certified to comply with ASME A112.19.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. 1. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Fig. 1 GENERAL DESCRIPTION: Roughing-in Dimensions SELECTRONIC™ PROXIMITY URINAL FLUSH VALVE DETECTION ZONE 400mm-800mm (15-3/4 TO 31-1/2) 72mm (2-7/8) FINISHED WALL 57mm (2-1/4 MIN.) 15˚ 116mm (4-5/8) MANUAL OVERRIDE BUTTON Valve is designed to provide stated flush volume with a 7.0 GPM flow rate. SUPPLY DN 19mm (3/4” I.P.S.) *CRITICAL LEVEL Right or Left Hand Installation -C-L- 115mm-134mm (4-1/2 TO 5-1/4) See (Section 5) for converting Flush Valve to Left Hand Installation.
PAGE 4
1 INSTALL SWEAT SOLDER Fig.3 Fig.3a ADAPTER; Fig. 3 CAUTION FINISHED WALL Turn water supplies off before beginning CENTER LINE OF FIXTURE SPUD A Note: Install Optional Sweat Solder Adapter (Supplied) for copper pipe supply line. Fig. 3. (A-B)= C 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. B 32mm (1-1/4) FILE EDGES 2. Cut the supply pipe 1-1/4" (A-B=C) shorter then the measurement taken in Step 1.
PAGE 5
4 FLUSH OUT SUPPLY LINES; Fig. 6 Fig. 6 2 1. Remove COVER (1) from SUPPLY STOP (2). REMOVE COVER 2. With a flat blade screwdriver open SUPPLY STOP (2). 1 3. Turn on water supply to flush line of any debris or sediment. 2 4. Close SUPPLY STOP (2) and replace COVER (1). COUNTER-CLOCKWISE OPENS CONTROL STOP CLOCKWISE CLOSES CONTROL STOP 453 LEFT OR RIGHT HAND INSTALLATION; Fig. 7 Fig. 7 The UNIT is shipped with the inlet flange on the right side.
PAGE 6
INSTALL FLUSH VALVE; Fig. 8a Fig. 8a & 8b 3 1. As shown in Fig. 8a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 8a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 8b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6). Make sure that GASKET (10) is installed.
PAGE 7
8 HOW TO RETROFIT OUR VALVE; Fig. 10 Fig. 10 Fig. 10a 6 (Replaces Industry Standard Manual and Electronic Valves) Note: In most Retrofits the wall escutcheon, supply stop, cover tube and vacuum breaker do not have to be replaced. If these items do need replacement they must be purchased separately or order the complete flush valve assembly from American Standard. 2 Fig. 10b CLEAN CONNECTIONS 1 4 5 3 1. Remove COVER (1) from SUPPLY STOP (2) if installed. Fig. 10. 2. Turn water supply off. Fig. 10.
PAGE 8
11 HOW TO SET DETECTION RANGE 10 Fig. 13 (If Required) ; Fig. 13 & 14 Note: The detection distance is preset and is ideal for most installations. Should an adjustment be required follow the steps below. Fig. 13a Fig. 13b 6 3 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of top half of FLUSH VALVE (3). Fig. 13a. 2. Rotate CAP (3) to the right and pull off. Fig. 13b. 1 VIEW “A” 3. Turn CAP (3) over and disconnect GREY SENSOR WIRE (4) from BATTERY COVER (5). 4.
PAGE 9
8 M968541 REV.1.2 NO NO NO YES NO 1. CLOSE STOP VALVE, 2. REPLACE SOLENOID KIT. 3. RE-ASSEMBLE AND INSTALL UNIT. 4. OPEN STOP VALVE. YES TEST SENSOR. DISCONNECT GRAY FLAT WIRE FROM BATTERY COVER AND RE-CONNECT. SENSOR SHOULD FLASH FOR 5 SECONDS. DOES IT FLASH? NO LOOK FOR REPEATED DOUBLE FLASH ON SENSOR NO YES REPLACE SENSOR SEE STEP 10, page 6 in manual INSTALL NEW BATTERY RETRY AUTO FLUSH YES 1. COVER SENSOR FOR 10 SECONDS 2. UNCOVER SENSOR FOR 10 SECONDS.
PAGE 10
SELECTRONIC™ PROXIMITY URINAL FLUSH VALVE 0.125 GPF & (0.5 LPF) MODEL NUMBERS 6063.013 6590.525 M962665-0020130A COVER ASSEMBLY FOR FLUSH VALVE WITH 0.125 gpf (BATTERY INCLUDED) A923654-0070A BATTERY 6VCR-P2 A950223-0070130A SENSOR ASSEMBLY W/MTG. KIT. (0.