Installation Guide

9
HANDSHOWER INSTALLATION
(FOR MODEL 7005.901 ONLY)
TEST INSTALLED FAUCET
7
Turn VALVES (1) to "off" position.
Lift HANDSHOWER (3) from holder, direct spray into tub, lift
TRANSFER KNOB (4) to check HANDSHOWER (3) and HOSES for leaks.
Turn VALVES "off."
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) and LOCKNUT (4) from
underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (4).
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of TEE (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and ESCUTCHEON (1). ( Note: SPRAY HOLDER (6)
must be separate from ESCUTCHEON (1) to get HOSE (8)
thrrough ESCUTCHEON (1).] Install SEAL (9) and connect both
HOSES (8) and (10). INSTALL second SEAL (9) and connect
HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
6
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT (2) mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
3
4
5
7
8
10
9
9
11
6
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2007
1
4
1
3
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90˚.
2
M 9 6 8 6 3 8 R E V. 1. 1
IN MEXICO 01-800-839-12-00
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles.
8
Hex wench, supplied
To remove handles, reverse steps in STEP 4.
To remove SPOUT (1), proceed as follows:
Lift KNOB (2) and unscrew from TRANSFER ROD (7).
Remove SET SCREW (3) using 5 mm hex wrench supplied.
Lift SPOUT (1) off SHANK (4) carefully and remove RUBBER
RING (5).
Unscrew SHANK SLEEVE (6) and lift TRANSFER ROD (7) from
SHANK (4).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (5) is properly seated in its recess at the base of SPOUT (1).
Make certain SET SCREW (3) is properly aligned and tight so that
SPOUT (1) is locked in place.
3
7
5
4
6
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.
DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
CARE INSTRUCTIONS: