Installation Guide

ManualsBrandsAmerican Standard ManualsBathroom Sink Faucets7018101.278

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965804 (4/17)

INSTALL FAUCET

EDGEMERE

™

SINGLE LEVER MONOBLOCK

LAVATORY FAUCET

INSTALLATION

INSTRUCTIONS

7018.101

Screwdriver Adjustable Wrench Tubing CutterChannel Locks

Certied to comply with ANSI A112.18.1M

MOUNTING

SURFACE

Figure A

(OPTIONAL

DECK PLATE)

2000102P-YYY

CAUTION

Turn off hot and cold water

supplies before begining.

• Seat SEAL (2) into under side of FAUCET BODY (1).

• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN ASSEMBLY

(8) through the mounting hole of lavatory. Figure A.

• From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6), pulling

faucet to front of sink, so SUPPLIES (3) rests against mounting hole.

Before nal tightening, make sure collar on MOUNTING NUT (6) is

seated into RETAINING WASHER (5).

• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)

to complete faucet mounting.

COLLAR ON

MOUNTING NUT

Figure B

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS EDGEMERE™ 7018.101 SINGLE LEVER MONOBLOCK LAVATORY FAUCET Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Screwdriver 1 INSTALL FAUCET CAUTION Channel Locks Adjustable Wrench Tubing Cutter Turn off hot and cold water supplies before begining.
PAGE 2
POP-UP DRAIN Fig. A. • Remove CLEAR PLASTIC COVER (1). Fig. B. 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). DRAIN BODY 3 • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 4 2 3 REMOVE FLANGE Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING ON OFF 1 • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. COLD HOT • Remove AERATOR (3). • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). 3 CHECK DRAIN CONNECTIONS 4 • Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Sink. 5 • Release POP-UP KNOB (4) down and check all drain connections and “P” trap for leaks.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be Removed) or “Unlock” Mode (Stopper is removable). Locked Mode: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
EDGEMERE™ SINGLE LEVER MONOBLOCK LAVATORY FAUCET MODEL NUMBERS 7018.