Installation Instructions

ManualsBrandsAmerican Standard ManualsBathParadigm Battery Powered Single Hole Touchless Bathroom Faucet with Above-Deck Mixing 0.5 GPM in Polished Chrome

M965985 (11/18)

Certied to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@lixilamericas.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

Paradigm

™

Selectronic

Integrated

Faucet with Optional Above-Deck Mixing

& SmarTherm

MODEL NUMBERS

7025.1xx 702B.1xx

7025.2xx 702B.2xx

7025.3xx 702B.3xx

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any components

will void the warranty.

Product No’.s & Options 2

Specications 3

Faucet Installation 3

Electrical Installation 4-5

FAQ’s / Troubleshooting 9

Parts 10

Start-up / Maintenance 6-8

Summary of content (9 pages)

PAGE 1
Installation Inst ru ct io n s Paradigm™ Selectronic® Integrated Faucet with Optional Above-Deck Mixing & SmarTherm® MODEL NUMBERS 7025.1xx 702B.1xx 7025.2xx 702B.2xx 7025.3xx 702B.3xx CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No’.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. UNPACKING Remove the fitting and loose items from the carton. The illustration below shows all the fittings and loose items after they have been removed from the carton.
PAGE 3
Paradigm Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. Roughing-in Dimensions 189 mm (7-1/2") CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.
PAGE 4
Fig. 1 ELECTRICAL INSTALLATION 4 Product Page 3 PWRX Power Kit (PK00.WRK) 4 Plug-In AC Power Kit (PK00.PAC) 5 Hard-Wired AC Power Kit (PK00.HAC) 5 Multi-AC Power Kit (PK00.MAC) 5 4 3 2 1 Important: All faucets with the standard CR-P2 battery come preaseambled from the factory. No further action necessary. A PWRX 10 YEAR BATTERY SYSTEM; Fig. 1 BRACKET INSTALLATION PWRK™ VERSION; 1. Connect PWRX BATTERY PACK (1) to SENSOR CABLE (2). 2.
PAGE 5
B AC VERSIONS (HARD-WIRED / Fig. 2 PLUG-IN POWER SUPPLY); Fig. 2 1 Important: Turn off power to outlet or electrical box. FOR PLUG-IN VERSION; 1. Connect PLUG-IN AC POWER SUPPLY (2) to one end of the SINGLE AC ADAPTER (6). 2. Connect SENSOR CABLE (4) to the other end of the SINGLE AC ADAPTER (6). 3. Connect PLUG-IN AC POWER SUPPLY (2) to wall outlet. 10' EXTENSION 7 AC-DC CONVERTER 5 4 1 FOR HARD-WIRED VERSION; 1. Connect HARD-WIRED AC TRANSFORMER (3) to AC-DC CONVERTER (7). 2.
PAGE 6
D MAKE WATER SUPPLY Fig. 4 CONNECTIONS; Fig. 4 1. Turn off hot and cold water supplies before beginning. 2. Install INLINE FILTER (3) on each wall supply outlet. Be sure that INLINE FILTER (3) is inserted in the correct direction. (See Illustration) 3. Connect HOT FLEXIBLE SUPPLY (marked with red stripe) (1) to INLINE FILTER (3) on hot water control stop (4). Connect COLD FLEXIBLE SUPPLY (marked with blue stripe) (2) to INLINE FILTER (3) on cold water control stop (5).
PAGE 7
3 MAINTENANCE Fig. Fig. 67 TION DETECNE ZO A HAND WASH SENSOR OPERATION; Fig. 7 REMOVE PROTECTIVE FILM FROM SENSOR EYE WHEN INSTALLATION IS COMPLETE. PROTECTIVE FILM When the Sensor detects a user, the water immediately starts to flow. Water flow will stop 1.5 seconds after user is out of sensor range. This Comfort delay allows the user to comfortably move their hands without the water turning off.
PAGE 8
Fig. 12 D ADJUST OR REPLACE MAXIMUM OUTLET TEMPERATURE; Fig. 10 6 1. With the COVER off, the installer can reduce the maximum mixed water temperature by turning the THERMO VALVE (4) clockwise with a screwdriver. 4 2. Remove SCREW (6) and unthread THERMO VALVE (4). Replace with new THERMO VALVE (4). WARNING • Do not turn the THERMO VALVE (4) More than 1 turn. • The maximum mixed water temperature can not be increased due to ASSE 1070 requirements. E GENERAL CLEANING Fig. 10 1.
PAGE 9
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 NO NO YES 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. REPLACE SOLENOID WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR.