Installation Guide

ManualsBrandsAmerican Standard Manuals8 inch Widespread Sink FaucetsTropic 8 in. Widespread 2-Handle Mid-Arc Bathroom Faucet in Satin Nickel with Metal Speed Connect Pop-Up Drain

M968892 Rev. 1.3

SLOT

MOUNTING

SURFACE

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure

the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) ﬁrmly. Fig. A.

Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE

BODY (13). Repeat above steps for opposite VALVE BODY (13A).

Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).

From under side of mounting surface, install VALVE BODY (13) through valve

mounting holes. Threads of VALVE BODY (13) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread ADAPTER (10)

onto VALVE BODY (13) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

7038.801

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

TROPIC

Spread Lavatory Faucet with

INSTALL SPOUT

INSTALL VALVE BODY

13a

Place RUBBER RING (9) into ADAPTER (10).

5/16'' MIN.

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Fig. A.

Fig. B.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the rst time, every time.

Summary of content (7 pages)

PAGE 1
Installation Instructions 7038.801 TROPIC Spread Lavatory Faucet with Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Certified to comply with ANSI A112.18.1 Speed Connect™ Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) with the spline is facing up. Fig. A. Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) until snug against mounting surface. THREAD ON TO DECK ADAPTER 4 SPLINE END UP 1 3 Fig. A.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
TROPIC Spread Lavatory Faucet with POP-UP DRAIN MODEL NUMBER 7038.801 M962450-YYY0A LIFT ROD KNOB M922881-YYY0A AERATOR M962448-YYY0A ESCUTCHEON KIT M962248-0070A DECK ADAPTER KIT Replace the "YYY" with appropriate finish code CHROME SATIN NICKEL 002 295 M961733-0070A SPOUT MTG. KIT M961634-0070A VALVE MTG.