Installation & Assembly

ManualsBrandsAmerican Standard ManualsBathroom Remodel & Bathroom FixturesSelectronic Single Hole Bathroom Faucet

(In Toronto Area only: 1-905-3061093)

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-3061093)

SELECTRONIC

Proximity Integrated Faucet

with Optional Above-Deck Mixing

7055.105

7055.115

7056.105

7056.115

7055.205

7055.215

7056.205

7056.215

Platform with Universal Sensor

To l e a r n more a b o u t A m e r i c a n S t a n d a rd Faucets visit our we b s i t e a t : www.americanstandard-us.com

or U.S. customer's e-mail us at: faucetsupport@americanstandard.com

Installation Instructions

M 9 6 5 2 5 5 R EV. 1.6

• Flexible Selectronic

• Easy installation. All electronics in the spout; nothing below deck.

• User adjustable above-deck mixing uses ceramic disc

valve for dependability & long life

• Mixing handle can be removed for one time temperature

setting during installation

• Available in DC (Battery) & AC versions

Certiﬁed to comply with ASME A112.18.1M

Product No.'s & Options

Speciﬁcations

How to Install

Maintenance

FAQ,s

Replacement Parts

2-3

3-7

7-8

Summary of content (9 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s SELECTRONIC® Proximity Integrated Faucet with Optional Above-Deck Mixing • Flexible Selectronic® Platform with Universal Sensor • Easy installation. All electronics in the spout; nothing below deck. • User adjustable above-deck mixing uses ceramic disc valve for dependability & long life • Mixing handle can be removed for one time temperature setting during installation • Available in DC (Battery) & AC versions Product No.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions Fig. 1 191mm (7-1/2) FINISHED WALL OR BACKSPLASH MIN. 1" CLEARANCE 191mm (7-1/2) 165mm (6-1/2) 140mm (5-1/2) MOUNTING SURFACE 66mm ( 2-5/8) 38mm (1-1/2 ) 32mm (1-1/4) GENERAL DESCRIPTION: Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery) or AC power.
PAGE 4
3 MAKE WATER SUPPLY Fig. 2 CONNECTIONS; Fig. 2 1. Turn off hot and cold water supplies before beginning. 2. Connect HOSE ADAPTERS (3) to wall supplies (if required). Connect FLEXIBLE SUPPLIES (1, 2) directly to HOSE ADAPTERS (3). 2 1 3. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold supply. Use adjustable wrench to tighten connections. Do not over tighten. 3 SEAL WASHER (SUPPLIED) 4. Faucet supplies are 18" long from faucet base.
PAGE 5
2 HOW TO CHANGE SENSOR Fig. 2 RANGE; (Factory set at 6") Fig. 2 1. Setting the Detection Zone (Distance): Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. Fig. 2. REMOVE 1 REPLACE 2. Disconnect the BLACK POWER SUPPLY CONNECTOR (1) and reconnect. Fig. 3. 3 4 2 3. While the SENSOR CONTROL LED (2) is blinking slowly, place your hand 1 - 2 in. (25.4-50.
PAGE 6
3 HOW TO INSTALL AND CHANGE Fig. 5 BATTERY; Fig. 5 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. 1 2 2. Remove BATTERY HOLDER (1) from FAUCET BODY (2). 3. Remove old battery from the BATTERY HOLDER (1). 4. Install NEW BATTERY (3) into the BATTERY HOLDER (1). Replace BATTERY HOLDER (1) into the FAUCET BODY (2). 3 5.
PAGE 7
5 HOW TO CLEAN FILTER SCREEN Fig. 9 ON SOLENOID VALVE; Fig. 9 & 10 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. DISCONNECT WIRE CONNECTION 1 2. Disconnect WIRE CONNECTION (1) to SOLENOID VALVE (2). Fig. 9. 3. Unthread SOLENOID VALVE (2) from VALVE BODY (3). Fig. 9. 4.
PAGE 8
7 CHANGE HOT LIMIT SETTING FROM 95% TO 85%; Fig. 13 2 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. 3 9 2. Replace LEVER HANDLE and rotate counter-clockwise to its stop position (100% cold). Remove HANDLE. 8 SLOT 3. Pull out LIMITER STOP (1) from the VALVE STEM (2). 4.
PAGE 9
SELECTRONIC Proximity Integrated Faucet with Above-Deck Mixing PRODUCT NUMBERS 7055.105 7055.115 7056.105 7056.115 M900540-0020A FAUCET COVER (LESS MIXING) M900541-0020A FAUCET COVER (FOR MIXING VALVE) 7055.205 7055.215 7056.205 7056.215 A912790-0070A VALVE STEM O-RINGS A923654-0070A BATTERY 6VCR-P2 M964171-0070A 1.5 GPM AERATOR M964172-0070A 0.