Installation Sheet

ManualsBrandsAmerican Standard ManualsBathroom FaucetsStudio S 1.2 GPM Single Hole Vessel Bathroom Faucet with Grid Drain Assembly

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965781 Rev. 1.0 (1/18)

INSTALL FAUCET

STUDIO

VESSEL LAVATORY FAUCET

INSTALLATION

INSTRUCTIONS

7105.152

Screwdriver Adjustable Wrench Tubing CutterChannel Locks

Certied to comply with ANSI A112.18.1M

MOUNTING

SURFACE

CAUTION

Turn off hot and cold water

supplies before begining.

• Seat SEAL (1) into under side of FAUCET BASE (2).

• Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4)

through hole in mounting surface.

• From below, install SUPPORT PLATE (7) GASKET (5) and

MOUNTING NUT (6) onto SHANK (4). Secure Faucet with

MOUNTING NUT (6). Before nal tightening, adjust Faucet

so that it is centered. Tighten MOUNTING NUT (6) to

complete mounting.

Note: For thick deck installations, the SUPPORT PLATE (7)

can be omitted.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7105.152 STUDIO® S VESSEL LAVATORY FAUCET Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Screwdriver 1 INSTALL FAUCET CAUTION Channel Locks Adjustable Wrench Tubing Cutter Turn off hot and cold water supplies before begining.
PAGE 2
MAKE WATER SUPPLY AND WASTE CONNECTIONS • Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect right SUPPLY (2) to Hot (Marked with a Red Band) and left supply to COLD (1) wall supply. • Faucet supplies are 20" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking. • Connect 1-1/4" O.
PAGE 3
4 TEST INSTALLED FITTING 1 ON OFF COLD • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. HOT • Remove AERATOR (3). 3 • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). WASTE OUTLET 5 SERVICE CAUTION Turn off hot and cold water supplies before beginning. 2 • To remove or replace cartridge: – Turn valve to OFF position. 2 “P” TRAP – Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).
PAGE 4
STUDIO® S VESSEL LAVATORY FAUCET MODEL NUMBER M970230-YYY0A HANDLE KIT M970231-0070A GEAR AND PLUG KIT M951430-0070A CARTRIDGE 7105.152 Replace the “YYY” with appropriate finish code POLISHED CHROME 002 BRUSHED NICKEL 295 MATTE BLACK 243 M970248-YYY0A PLUG BUTTON & SCREW M923840-0070A AERATOR (1.2 GPM) M953455-YYY0A DRAIN COMPLETE A923480-0070A SUPPORT PLATE 070532-0040A TAILPIECE HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Mon. - Fri.