Installation Instructions

ManualsBrandsAmerican Standard ManualsBathStudio S Vessel Sink Faucet with 1.2 GPM in Chrome

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965781 (3/17)

INSTALL FAUCET

STUDIO

MONOBLOCK LAVATORY FAUCET

INSTALLATION

INSTRUCTIONS

7105.15XT

Screwdriver Adjustable Wrench Tubing CutterChannel Locks

Certied to comply with ANSI A112.18.1M

GROOVE

(FAUCET

BASE)

MOUNTING

SURFACE

Figure A

CAUTION

Turn off hot and cold water

supplies before begining.

• Seat SEAL (1) into under side of ESCUTCHEON RING (2).

• Seat ESCUTCHEON RING (2) with collar facing up into groove in

faucet base.

• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) through

ESCUTCHEON RING (2) and the mounting hole of lavatory or

mounting surface. Figure A.

• From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6), pulling

faucet to front of sink, so SUPPLIES (3) rests against mounting hole.

Before nal tightening, make sure collar on MOUNTING NUT (6) is

seated into RETAINING WASHER (5).

• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)

to complete faucet mounting.

COLLAR ON

MOUNTING NUT

Figure B

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7105.15XT STUDIO® S MONOBLOCK LAVATORY FAUCET Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Screwdriver 1 INSTALL FAUCET CAUTION Channel Locks Adjustable Wrench Tubing Cutter Turn off hot and cold water supplies before begining.
PAGE 2
MAKE WATER SUPPLY AND WASTE CONNECTIONS • Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect right SUPPLY (2) to Hot (Marked with a Red Band) and left supply to COLD (1) wall supply. • Faucet supplies are 20" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (1, 2) are to long, loop as illustrated to avoid kinking. • Connect 1-1/4" O.
PAGE 3
4 TEST INSTALLED FITTING 1 ON OFF COLD • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. HOT • Remove AERATOR (3). 3 • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). WASTE OUTLET 5 SERVICE CAUTION Turn off hot and cold water supplies before beginning. 2 • To remove or replace cartridge: – Turn valve to OFF position. 2 “P” TRAP – Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).
PAGE 4
STUDIO® S MONOBLOCK LAVATORY FAUCET MODEL NUMBER M970230-YYY0A HANDLE KIT M970231-0070A GEAR AND PLUG KIT 7105.15X Replace the “YYY” with appropriate finish code POLISHED CHROME 002 BRUSHED NICKEL 295 M951430-0070A CARTRIDGE M970248-YYY0A PLUG BUTTON & SCREW M923840-0070A AERATOR (1.2 GPM) 015025-YYY0A DRAIN COMPLETE A923480-0070A 070532-0040A TAILPIECE HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Mon. - Fri. 8:00 a.m. to 8:00 p.m.