Installation & Assembly

ManualsBrandsAmerican Standard ManualsBathroom Remodel & Bathroom FixturesStudio S 8" Widespread Bathroom Faucet with Drain Assembly

- 1 -

SPOUT BASE

Fig. A.

Fig. B.

13 Blue Stripe (COLD)

13 Red Stripe

(HOT)

13a

11a

Product names listed herein are trademarks of AS America, Inc.

Congratulations on purchasing your American Standard faucet

with Speed Connect drain, a feature found only on American

Standard faucets.

Speed Connect

Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the rst time, every time.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

RECOMMENDED TOOLS

M965780 (6/17)

INSTALL SPOUT

STUDIO

DUAL CONTROL WIDESPREAD

LAVATORY FAUCET

WITH SPEED CONNECT

DRAIN

INSTALLATION

INSTRUCTIONS

7105.801

7105.821

Flat Head Screwdriver

Adjustable Wrench Tubing CutterSlip Jaw Pliers

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

INSTALL VALVE BODIES

Fig. A.

• Insert SHANK (1) CABLE CONNECTOR (2) and HOSE (3) through center hole,

making sure SEAL WASHER (4) is properly seated in spout base.

• From below, push GASKET (6) with RETAINING WASHER (7) onto MOUNTING

STUD (5). Secure faucet with MOUNTING NUT (8), pushing faucet to back of

sink, so SUPPLIES (3) rests against mounting hole.

• Align and center SPOUT (1). Tighten LOCKNUT (6).

Hex Wrench

Fig. B.

• Place SEAL WASHER (8) under HANDLE (9) and

make sure it sits properly inside the groove of the

deck adapter.

• Remove LOCKNUT (10) and RUBBER WASHER

(11), FRICTION WASHER (11a) from SIDE VALVE

SHANKS (12).

• Insert Hot and Cold SIDE VALVE HOSES (13),

FLEXIBLE SUPPLIES (13a) into mounting holes

making sure the SEAL WASHERS (8) are

properly seated in each HANDLE BASE (9).

• Assemble SPACER (14) RUBBER WASHER (11),

FRICTION WASHER (11a) and thread LOCKNUT

(10) onto each SIDE VALVE SHANK (12) from

underside of sink or mounting surface.

NOTE: SPACER (14) not needed for deck

thickness larger then 3-1/4".

• Align and center SIDE VALVES. Tighten

LOCKNUTS (10).

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS STUDIO® S 7105.801 7105.821 DUAL CONTROL WIDESPREAD LAVATORY FAUCET WITH SPEED CONNECT® DRAIN Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect® Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY • Tighten TAIL PIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tail piece on pop-up drain is 1-1/4" O.D. Fig. B. 2 1-1/4" O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Remove AERATOR (3). 3 1 • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). 5 11 CHECK DRAIN CONNECTIONS 1 • Operate POP-UP KNOB (5) and fill lavatory with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If DRAIN STOPPER (4) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
STUDIO® S DUAL CONTROL WIDESPREAD LAVATORY FAUCET WITH SPEED CONNECT® DRAIN M970247-YYY0A LIFT ROD AND KNOB MODEL NUMBERS 7105.801 7105.