Installation Guide

ManualsBrandsAmerican Standard ManualsBathroom Sink FaucetsPatience Polished Nickel 1-handle Single Hole WaterSense Bathroom Sink Faucet with Drain

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965817 (6/17)

INSTALL FAUCET

PATIENCE

MONOBLOCK LAVATORY FAUCET

WITH SPEED CONNECT

DRAIN

INSTALLATION

INSTRUCTIONS

7106.101

Screwdriver Adjustable WrenchChannel Locks

Certied to comply with ANSI A112.18.1M

COLLAR ON

MOUNTING NUT

GROOVE

(FAUCET

BASE)

MOUNTING SURFACE

Fig. C.

Fig. B.

Fig. A.

PUTTY

IF REQUIRED

CAUTION

Turn off hot and cold water

supplies before begining.

• Installation with ESCUTCHEON PLATE: (optional) must be purchased separately: Apply a light

bead of plumbers putty to underside of ESCUTCHEON PLATE (8) if mounting surface is uneven.

Place ESCUTCHEON PLATE (8) onto sink or mounting surface. Feed FAUCET SUPPLIES (3),

MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8) through ESCUTCHEON PLATE (8) and

mounting hole of lavatory or mounting surface. Fig. A.

• Installation less ESCUTCHEON PLATE: Seat SEAL (1) into under side of FAUCET BASE (2).

• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAINCABLE ASSEMBLY (8)

through the mounting hole of lavatory or mounting surface. Fig. B.

• From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),

pulling faucet to front of sink, so SUPPLIES (3) rests

against mounting hole. Before nal tightening, make

sure collar on MOUNTING NUT (6) is seated into

RETAINING WASHER (5). Fig. C .

• Adjust Faucet so that it is centered. Tighten

MOUNTING NUT (6) to complete faucet mounting.

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PATIENCE 7106.101 MONOBLOCK LAVATORY FAUCET WITH SPEED CONNECT® DRAIN Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Screwdriver 1 INSTALL FAUCET CAUTION Channel Locks Adjustable Wrench Turn off hot and cold water supplies before begining.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpipe on pop-up drain is 1-1/4" O.D. Fig. B. 2 1-1/4" O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING ON 1 • Move HANDLE (1) into “off” position. OFF COLD HOT • Remove AERATOR (3) and clean if necessary. • Turn on water supplies and check all connections for leaks. • Operate HANDLE (1) to flush water lines thoroughly. 3 • Replace AERATOR (3). CHECK DRAIN CONNECTIONS • Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Sink.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be Removed) or “Unlock” Mode (Stopper is removable). Locked Mode: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
PATIENCE MONOBLOCK LAVATORY FAUCET WITH SPEED CONNECT® DRAIN M964369-YYY0A PLUG BUTTON & SCREW MODEL NUMBER M970288-YYY0A HANDLE KIT 7106.