Installation Guide

ManualsBrandsAmerican Standard ManualsBathroom Sink FaucetsPatience Brushed Nickel 1-Handle Single Hole Watersense Bathroom Sink Faucet with Drain

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965830 (6/17)

INSTALL LAVATORY FAUCET

PATIENCE

VESSEL LAVATORY FITTING

INSTALLATION

INSTRUCTIONS

7106.152

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

Adjustable Wrench

Channel Locks

Regular Screwdriver

Phillips Screwdriver

Plumbers' Putty or Caulking

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

GROOVE IN

(FAUCET BASE)

MOUNTING

SURFACE

• Seat SEAL (1) into under side of ESCUTCHEON RING (2).

• Seat ESCUTCHEON RING (2) with collar facing up into groove

in faucet base.

• Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4) through

ESCUTCHEON RING (2) and hole in mounting surface.

• From below, install SUPPORT PLATE (7) GASKET (8) and RETAINING

WASHER (5) onto MOUNTING STUD (4). Secure Faucet with MOUNTING

NUT (6), pulling faucet to front of sink, so SUPPLIES (3) rests against

mounting hole. Before nal tightening, make sure collar on MOUNTING

NUT (6) is seated into RETAINING WASHER (5). Fig. C .

• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to complete

faucet mounting.

Note: For thick deck installations, the SUPPORT PLATE (7) can be omitted.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7106.152 PATIENCE VESSEL LAVATORY FITTING Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Regular Screwdriver Adjustable Wrench Plumbers' Putty or Caulking Phillips Screwdriver Channel Locks CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.
PAGE 2
MAKE WATER SUPPLY CONNECTIONS • Turn off hot and cold water supplies before beginning. • Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connectleft supply to Hot and right supply to the Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten. • Faucet supplies are 28" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately.
PAGE 3
4 TEST INSTALLED FAUCET AND CHECK OFF FOR LEAKS ON HOT 1 • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Remove AERATOR (3). COLD 3 • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). HOT COLD 2 5 SERVICE CAUTION Turn off hot and cold water supplies before beginning. 3 • To remove or replace cartridge: Fig. A. – Turn valve to OFF position. – Remove HANDLE SCREW (2). – Pull off HANDLE (3) and CAP (4).
PAGE 4
PATIENCE VESSEL LAVATORY FITTING MODEL NUMBER M964369-YYY0A PLUG BUTTON & SCREW 7106.