Installation Guide

ManualsBrandsAmerican Standard ManualsBathroom Sink FaucetsPatience Polished Nickel 2-Handle Widespread Watersense Bathroom Sink Faucet with Drain

- 1 -

SPOUT BASE

Fig. A.

Fig. B.

13 Blue Stripe (COLD)

13 Red Stripe

(HOT)

13a

Product names listed herein are trademarks of AS America, Inc.

RECOMMENDED TOOLS

M965818 (8/17)

INSTALL SPOUT

PATIENCE

DUAL CONTROL WIDESPREAD

LAVATORY FAUCET

WITH SPEED CONNECT

DRAIN

INSTALLATION

INSTRUCTIONS

7106.8X1

Flat Head Screwdriver

Adjustable Wrench Tubing CutterSlip Jaw Pliers

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

INSTALL VALVE BODIES

Fig. A.

• Insert SHANK (1) CABLE CONNECTOR (2) and HOSE (3) through center

hole, making sure SEAL WASHER (4) is properly seated in spout base.

• From below, Install RUBBER SEAL with RETAINING WASHER (5) and

LOCKNUT (6) onto faucet SHANK (1). Before nal tightening, faucet

should be seated ush on mounting surface.

• Align and center SHANK (1). Tighten LOCKNUT (6).

Hex Wrench

Fig. B.

• Place SEAL WASHER (8) under HANDLE (9) and

make sure it sits properly inside the groove of the

deck adapter.

• Remove LOCKNUT (10) and RUBBER WASHER

(11) from SIDE VALVE SHANKS (12).

• Insert Hot and Cold SIDE VALVE HOSES (13),

FLEXIBLE SUPPLIES (13a) into mounting holes

making sure the SEAL WASHERS (8) are

properly seated in each HANDLE BASE (9).

• Assemble RUBBER WASHER (11), and thread

LOCKNUT (10) onto each SIDE VALVE SHANK

(12) from underside of sink or mounting surface.

• Align and center SIDE VALVES. Tighten

LOCKNUTS (10).

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7106.8X1 PATIENCE DUAL CONTROL WIDESPREAD LAVATORY FAUCET WITH SPEED CONNECT® DRAIN Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Flat Head Screwdriver 1 INSTALL SPOUT Slip Jaw Pliers CAUTION Fig. A.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY • Tighten TAIL PIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tail piece on pop-up drain is 1-1/4" O.D. Fig. B. 2 1-1/4" O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING 5 • Move HANDLE (1) into “off” position. 1 • Remove AERATOR (3) and clean if necessary. • Turn on water supplies and check all connections for leaks. 3 • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). 1 11 CHECK DRAIN CONNECTIONS • Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Sink.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Fig. G. • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
PATIENCE DUAL CONTROL WIDESPREAD LAVATORY FAUCET WITH SPEED CONNECT® DRAIN MODEL NUMBERS M970286-YYY0A LIFT ROD AND KNOB 7106.8X1 M970285-YYY0A LEVER HANDLE M923840-0070A AERATOR (1.