Dimensions Guide

ManualsBrandsAmerican Standard Manuals8 inch Widespread Sink FaucetsFluent 8 in. Widespread Bathroom Faucet with Speed Connect Drain in Polished Chrome

SPREAD LAVATORY

FAUCETS

Installation

Instructions

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Certiﬁed to comply with ANSI A112.18.1M

M968508 (11/15)

Insert SPOUT SHANK (1) through center hole of mounting surface, making sure

RUBBER GASKET (2) is properly positioned in SPOUT BASE (3).

SPOUT OR BASE ASSEMBLY

Assemble RUBBER WASHER (4), BRASS WASHER (5), and LOCKNUT (6) onto threads of

SPOUT SHANK (1) from underside of mounting surface.

Align SPOUT (7) and tighten LOCKNUT (6). Be sure slot in BRASS WASHER (5) is

positioned to the rear as shown.

Turn off water at

main supply.

CAUTION

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

TO CHANGE SPOUT TO A SWIVEL SPOUT:

Unscrew SPOUT NUT (8) and remove SPOUT (7).

Take SPOUT CLIP (9) off SPOUT (7) and remove RUBBER RING (10).

Replace RUBBER RING (10) with seperate PLASTIC RING (11) packed with faucet.

Put SPOUT CLIP (9) on SPOUT (7).

Reassemble SPOUT (7) to SPOUT BASE (3).

6540.140

6540.160

6540.168

6540.170

6542.140

6542.170

6542.145

6540.175

6542.175

6540.270

6540.275

6540.278

6540.277

Summary of content (4 pages)

PAGE 1
Installation Instructions 6540.140 6540.160 6540.168 6540.170 6542.140 6542.170 SPREAD LAVATORY FAUCETS 6542.145 6540.175 6542.175 6540.270 6540.275 6540.278 6540.277 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. Certified to comply with ANSI A112.18.1M M968508 (11/15) To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
PAGE 2
VALVE ASSEMBLY WITH FLEXIBLE HOSE VALVE CONNECTIONS Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks. Insert VALVES (5) into mounting holes from underside of ledge. Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto valves until snug against internal stop. 10 11 Tighten LOCKNUT (1) to secure VALVE (5) position. 10 11 3 11 5/16'' MIN.
PAGE 3
2b VALVE ASSEMBLY WITH RIGID VALVE CONNECTIONS Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks. Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5) into mounting holes from underside of ledge. 10 Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and attach to SPOUT SHANK (7) and tighten.
PAGE 4
SPREAD LAVATORY FAUCETS MODEL NUMBERS M919646-0020A 5" SPOUT M953429-0020A 8" SPOUT 051211-0070A INDEX KIT 066114-0020A AERATOR, 0.5gpm M922858-0020A AERATOR, 0.35gpm M922880-0020A AERATOR, 1.5gpm 000690-0020A HANDLE SCREW 051210-0020A LEVER HANDLE M918014-0070A ADAPTER 051211-0070A INDEX KIT M964478-0020A 6" WRIST BLADE HANDLE (6400.160, 6400.